Bedienungsanleitung Philips 32PFL3208H (Seite 58 von 74) (Englisch)

525299

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

EN 58

Wired connection

1. Switch on the router and switch on its

DHCP setting.

2. Connect the router to the TV with an

Ethernet cable.

3. Press , then select [Setup].

4. Select [Connect to network], then press

OK.

5. Follow the onscreen instructions to install

the network.

6. Wait for the TV to find the network

connection.

7. If you are prompted, agree to the End

User Licence Agreement.

Wi-Fi ready

This section is for PFL32x8 only.

With the Philips wireless USB adapter

PTA128 (sold separately), you can connect

the TV to your home network wirelessly.

Note:

The wireless network operates in the same

2.4GHz frequency spectrum as common

household devices, such as Dect phones,

microwave ovens or Bluetooth devices,

which can cause Wi-Fi interference. Move

these devices away from the TV.

 To reduce network traffic, switch off

unused network equipment in the

home network.

 Reception quality depends on the

location of the wireless router and the

local Internet service provider.

 When playing video over your wireless

home network, we recommend that

you use an IEEE 802.11 N router. The

connection speed may differ according

to the operating environment of your

wireless home network.

Start wireless setup

1. Switch on your wireless network router.

2. Connect the Philips USB adapter PTA128

to a USB connector on the TV.

The wireless installation starts automatically.

3. Follow the onscreen instructions.

Tip: Keep the wireless USB adapter

connected to the TV.

WPS - Wi-Fi Protected Setup

1. If your router supports Wi-Fi Protected

Setup (WPS), press the WPS button on the

router.

2. After 2 minutes, select [WPS] on the TV,

then press OK.

The TV connects to your network. This

takes about 2 minutes.

Most new wireless routers have the WPS

system and carry the WPS logo. The WPS

system uses WPS security encryption and

cannot be combined with devices on your

network that use the WEP security

encryption. If you still need the WEP (Wired

Equivalent Privacy) devices in your network,

install with [Scan] > [Custom].

Scan for routers

If you have several routers in your network,

you can select the network you need.

1. To select a specific network router, press

[Scan] on the first page of the installation.

The routers with WPS and the strongest

signal are shown first in the list on screen.

2. Select the router you need, then press

OK.

 If you are connecting to a WPS router,

select [WPS] on the TV.

 If you want to set the PIN code in your

router software to connect, select

[WPS pin]and note down the code.

 To enter the encryption key manually,

select [Standard], then enter the key

when prompted.

Set secured connection with WPS PIN

1. To set secured connection, select the

[WPS pin] and press OK.

2. Write down the 8-digit PIN code shown

on TV, then enter it into the router software

on your PC.

To find out where to enter the PIN code,

read the router manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 32PFL3208H Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips 32PFL3208H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info