811228
47
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
45
12. Troubleshooting &
FAQs
12.1 Troubleshooting
This page deals with problems that can
be corrected by a user. If the problem
persists after you have tried these
solutions, contact a Philips customer
service representative.
Common Problems
No Picture (Power LED not lit)
Make sure the power cord is
plugged into the power outlet and
the back of the monitor.
First, ensure that the power button
on the front of the display is in the
OFF position, then press it to the ON
position.
No Picture (Power LED is White)
Make sure the computer is turned
on.
Make sure the signal cable is
properly connected to your
computer.
Make sure the monitor cable has no
bent pins on the connecting side. If
yes, repair or replace the cable.
The Energy Saving feature may be
activated Screen says
  
Make sure the display cable
is properly connected to your
computer. (Also refer to the Quick
Start Guide).
Check to see if the display cable has
bent pins.
Make sure the computer is turned
on.
Visible signs of smoke or sparks
Do not perform any troubleshooting
steps
Disconnect the monitor from the
mains power source immediately for
safety
Contact Philips customer service
representative immediately.
Imaging Problems
The image appears blurred, indistinct, or
too dark
Adjust the contrast and brightness
on On-Screen Display.
An "after-image", "burn-in" or "ghost
image" remains after the power has
been turned o.
Uninterrupted display of still or
static images over an extended
period may cause "burn-in", also
known as "after-imaging" or "ghost
imaging", on your screen. "Burn-in ",
"after-imaging", or "ghost imaging"
is a well-known phenomenon in LCD
panel technology. In most cases, the
"burn-in" "after-imaging" or "ghost
imaging" will disappear gradually
over some time after the power has
been switched off.
Always activate a moving screen
saver program when you leave your
display unattended.
Always activate a periodic screen
refresh application if your LCD
display will display unchanging static
content.
Failure to activate a screen saver, or
a periodic screen refresh application
may result in severe “burn-in”,
after-imaging” or “ghost imaging”
47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Philips 40B1U6903CH wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Philips 40B1U6903CH

Philips 40B1U6903CH Bedienungsanleitung - Holländisch - 53 seiten

Philips 40B1U6903CH Bedienungsanleitung - Französisch - 55 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info