Bedienungsanleitung Philips 42PFL3208K (Seite 39 von 74) (Englisch)

525805

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

EN 39

English

Satellite settings

What you can do

This TV can receive signals from 4 different

low noise block-down converters (LNBs).

An LNB is mounted at the end pole of the

dish antenna and captures signals from a

satellite.

Note:

 Satellite reception is available for certain

models only. [Search for satellite] is

only available if the TV supports DVB-S.

 To receive satellite channels, connect a

satellite receiver to the SAT connector

on your TV.

Install satellite channels

Reinstall satellites

1. While you watch TV, press .

2. Select [Setup] > [Search for satellite] >

[Reinstall satellites].

3. Follow the onscreen instructions to

complete the installation.

4. Once complete, select [Finish], then press

OK.

Select connection type

When you install satellite channels, you need

to set the connection type. The number of

LNBs on your dish antenna determines the

number of satellite channels you can install.

1. While you reinstall satellites, select

[Settings], then press OK.

2. Select [Connection type].

3. Select a setting, then press OK.

 [1 satellite (Single LNB)]: Select if you

have only one LNB.

 [2 satellites (DiSEqC Mini)]: Select if

you have 2 LNBs.

 [3 or 4 satellites (DiSEqC 1.0)]: Select

for 3 or 4 LNBs.

 [Unicable for 1 satellite]: Select if you

have a Unicable setup with 1 satellite.

 [Unicable for 2 satellites]: Select if you

have a Unicable setup with 2 satellite.

Manual installation

If a transponder is skipped during installation,

you can test the signal strength of a

transponder or add a new transponder.

1. While you watch TV, press .

2. Select [Setup] > [Search for satellite] >

[Manual installation], then press OK.

3. Select the LNB.

4. If you know the frequency of the

transponder (which can include several

channels), select [Frequency]and set the

frequency.

5. Select [Search], then press OK.

6. If a new frequency is found, press

[Store]to add the new transponder with its

channels.

Update satellite channels

1. While you watch TV, press .

2. Select [Setup] > [Search for satellite] >

[Update channels].

3. Follow the onscreen instructions to

complete the installation.

4. Once complete, select [Finish], and then

press OK.

Add and remove satellites

You can add or remove satellites at any

time, and install channels from new satellites.

Note: Before you add satellites, make sure

that the connection type is correct. See

Change your TV settings > Satellite Settings

> Install satellite channels (Page 39).

1. Press .

2. Select [Setup] > [Search for satellite],

then press OK.

3. Select [Add satellite], then press OK.

The TV searches for a satellite on the first

free LNB. This can take several minutes.

4. If no satellite is found, check the antenna

connections and the position of the dish

antenna, then select [Search again].

5. If you are satisfied with the added satellite,

select [Next] to install all channels from the

satellite.

The installation can take several minutes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 42PFL3208K Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips 42PFL3208K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info