Bedienungsanleitung Philips 42PFL3527H (Seite 29 von 61) (Englisch)

523836

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

EN 29

English

Satellite settings

What you can do

View satellite channels

Note:

 Satellite signal is available on certain

models only.

[Search for satellite] is only available if

the TV supports DVB-S.

 To receive satellite channels, connect a

satellite receiver to the SAT connector

on your TV.

LNBs

This TV can receive signals from 4 different

low noise block-down converters (LNBs).

An LNB is mounted at the end pole of the

dish antenna and captures signals from a

satellite.

Install satellite channels

1. While you watch TV, press .

2. Select [Setup] > [Search for satellite] >

[Reinstall channels].

3. Follow the onscreen instructions to

complete the installation.

4. Once complete, select [Finish], then press

OK.

Select connection type

While you install satellite channels, you need

to set the connection type. The number of

LNBs on your dish antenna determines the

number of satellite channels you can install.

1. After you select [Reinstall channels],

select [Settings] and then press OK.

2. Select [Connection type].

3. Select a setting, then press OK.

 [OneLNB]: Select if you have only one

LNB.

 [DiSeqC Mini (2 LNBs)]: Select if you

have 2 LNBs.

 [DiSeqC 1.0 (3-4 LNBs)]: Select for 3

or 4 LNBs.

Test signal strength

If a channel or transponder is skipped during

installation, you can test the signal strength of

a satellite or add a new channel.

1. While you watch TV, press .

2. Select [Setup] > [Search for satellite] >

[Satellite reception test], then press OK.

3. Select the LNB.

4. If you know the frequency of the

transponder (which can include several

channels), select [Frequency] and enter it.

5. Select [Search], then press OK.

6. If a new frequency is found, press

[Store]to add the new transponder with its

channels.

Update satellite channels

1. While you watch TV, press .

2. Select [Setup] > [Search for satellite] >

[Update channels].

3. Follow the onscreen instructions to

complete the installation.

4. Once complete, select [Finish], then press

OK.

Add and remove satellites

You can add or remove satellites at any time,

and install channels from new satellites.

Note: Before you add satellites, make sure

that the connection type is correct. See Set

up your TV > Satellite Settings > Install

channels (Page 29).

1. Press > [Setup] > [Search for

satellite], then press OK.

2. Select [Add satellite], then press OK.

The TV searches for a satellite on the first

free LNB. This can take several minutes. If no

satellite is found, check the antenna

connections and the position of the dish

antenna.

3. If no satellite is found, select [Restart].

 If you are satisfied with the added

satellite, install the channels.

4. To install all channels, select [Install]. The

installation can take several minutes.

Remove a satellite

1. Press > [Setup] > [Search for

satellite].

2. Select [Remove satellite], then press OK.

3. Select the satellite you want to remove,

then press OK.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 42PFL3527H Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips 42PFL3527H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info