Bedienungsanleitung Philips 47PFL5038H (Seite 39 von 74) (Englisch)

525589

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

EN 39

English

Step 1: Check the country setting

1. Switch on the first TV (with the channels

that you want to copy to the second TV).

2. Press .

3. Select [Setup] > [Search for channels] >

[Reinstall channels], then press OK.

The country menu is displayed.

4. Make a note of the current setting.

5. Press .

6. Press [Cancel] to exit.

Step 2: Copy channel list to USB

1. Connect a USB storage device to the first

TV (with the channels installed on it).

2. Press .

3. Select [Setup] > [Channel settings] or

[Satellite settings].

4. Select [Channel installation] > [Copy

channel list] > [Copy to USB], then press

OK.

The channel list is copied to the USB storage

device.

5. Disconnect the USB storage device.

Step 3: Copy channels to a TV with no

channels installed

1. Switch on the second TV, on which you

want to copy the channel list.

Initial installation starts.

2. Follow the onscreen instructions and

select the same country as the TV whose

channel list you want to copy.

3. Skip the search for channels.

4. Connect the USB storage device.

5. Press .

6. Select [Setup] > [Channel settings] or

[Satellite settings].

7. Select [Channel installation] > [Copy

channel list] > [Copy to TV], then press

OK.

The channel list is copied to the TV storage

device.

8. Disconnect the USB storage device.

Step 3: Copy channels to a TV with pre-

installed channels

1. Switch on the second TV, on which you

want to copy the channel list.

2. Press .

3. Select [Setup] > [Search for channels] >

[Reinstall channels], then press OK.

The country menu is displayed.

4. Make sure that the country setting is the

same as for the first TV.

5. Press .

6. Press [Cancel] to exit.

7. If the country setting is different, reinstall

the second TV to match the country setting

of the first TV. See Change your TV settings

> Reset all (Page 44).

8. Connect the USB storage device to the

second TV.

9. Press .

10. Select [Setup] > [Channel settings] or

[Satellite settings].

11. Select [Channel installation] > [Copy

channel list] > [Copy to TV], then press

OK.

The channel list is copied to the second TV.

12. Disconnect the USB storage device.

Satellite settings

What you can do

This TV can receive signals from 4 different

low noise block-down converters (LNBs).

An LNB is mounted at the end pole of the

dish antenna and captures signals from a

satellite.

Note:

 Satellite reception is available for certain

models only. [Search for satellite] is

only available if the TV supports DVB-S.

 To receive satellite channels, connect a

satellite receiver to the SAT connector

on your TV.

Install satellite channels

Reinstall satellites

1. While you watch TV, press .

2. Select [Setup] > [Search for satellite] >

[Reinstall satellites].

3. Follow the onscreen instructions to

complete the installation.

4. Once complete, select [Finish], then press

OK.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 47PFL5038H Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips 47PFL5038H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info