Bedienungsanleitung Philips avent dect baby monitor (Seite 9 von 236) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

368389

Zoom out

Zoom in

Vorherige Seite

1/236

Nächste Seite

Mains operation

1 Put the large appliance plug in the baby unit and put the adapter in a wall socket (Fig. 2).

Operation on non-rechargeable batteries

The baby unit runs on four 1.5V R6 AA batteries (not included). We strongly advise you to use

Philips LR6 PowerLife batteries.

Do not use rechargeable batteries, as the baby unit does not have a charging function.

Place batteries in the baby unit if you do not want to use it from the mains or if you want to be

sure of backup power in case of mains failure. Replace the batteries when the baby unit indicates

that the batteries are low (the empty battery symbol ashes on the display and the text ‘Battery

low’ appears).

Unplug the baby unit and make sure your hands and the unit are dry when you insert the

non-rechargeable batteries.

1 Remove the lid of the compartment for non-rechargeable batteries (Fig. 3).

2 Insert four non-rechargeable batteries (Fig. 4).

Note: Make sure the + and - poles point in the right direction.

3 Reattach the lid (Fig. 5).

Parent unit

Operation on rechargeable battery pack

The parent unit comes with a rechargeable Li-ion 1000mAh battery pack.

Charge the parent unit before you use it for the rst time or when the parent unit indicates that the

battery is low (the empty battery symbol ashes on the display and the parent unit beeps). The

parent unit starts indicating that the battery pack is low 30 minutes before the battery pack is

completely empty.

Note: If the rechargeable battery pack is completely empty, the parent unit automatically switches off

and loses contact with the baby unit.

1 Remove the lid of the compartment for the rechargeable battery pack (Fig. 6).

2 Insert the rechargeable battery pack (Fig. 7).

3 Reattach the lid (Fig. 8).

4 Insert the small appliance plug into the charger, put the adapter in a wall socket and place the

parent unit in the charger (Fig. 9).

, The charging light on the charger goes on.

, The display shows a charging battery symbol to indicate that the parent unit is charging.

5 Leave the parent unit in the charger until the battery pack is fully charged.

, During charging, the charging light on the charger lights up continuously.

, When the battery pack is fully charged, the display of the parent unit shows a full battery

symbol T.

- When you charge the parent unit for the rst time or after a long period of disuse, switch it

off and let it charge continuously for at least 10 hours.

- Charging normally takes 4 hours, but it takes longer when the parent unit is switched on while

charging. To keep the charging time as short as possible, switch off the parent unit during

charging.

- When the battery pack is fully charged, the parent unit can be used cordlessly for up to 24

hours.

Note: When the parent unit is charged for the rst time, the operating time is less than 24 hours. The

battery pack only reaches its full capacity after you have charged and discharged it four times.

ENGLISH 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips avent dect baby monitor Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info