Bedienungsanleitung Philips-Avent SCD600 (Seite 13 von 164) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

507144

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite



This chapter lists the questions most frequently asked about the appliance. If you cannot nd the

answer to your question, contact the Consumer Care Centre in your country.

Question Answer

Why don’t the power-on

light of the baby unit and

the parent unit go on

when I switch on the

units?

Perhaps the rechargeable battery of the parent unit is empty and the

parent unit is not connected to the mains. Insert the appliance plug

into the parent unit and put the adapter in a wall socket. Then move

the volume wheel in the ‘ON’ direction to switch on the parent unit

and to establish connection with the baby unit.

Perhaps the baby unit is not connected to the mains and the non-

rechargeable batteries in the baby unit are empty or there are no

non-rechargeable batteries in the baby unit at all. Put full non-

rechargeable batteries in the baby unit or connect the baby unit to

the mains. Then set the on/off switch to ‘ON’ to switch on the baby

unit and to establish connection with the parent unit.

Why does the LINK light

on the parent unit ash

red?

The baby unit and the parent unit are out of range of each other.

Move the parent unit closer to the baby unit.

The baby unit may be switched off. Switch on the baby unit.

Why does the battery/

power-on light on the

parent unit ash green?

The rechargeable battery of the parent unit is running low. Recharge

the battery (see chapter ‘Preparing for use’).

Why does the parent

unit beep?

If the parent unit beeps while the LINK light lights up red continuously,

the connection with the baby unit is lost. Move the parent unit closer

to the baby unit.

The baby unit may be switched off. Switch on the baby unit.

Why does the video

monitor produce a high-

pitched noise?

The units may be too close to each other. Make sure the parent unit

and the baby unit are at least 1 metre/3 feet away from each other.

The volume of the parent unit may be set too high. Decrease the

volume of the parent unit.

Why don’t I hear a

sound/Why can’t I hear

my baby cry?

The volume of the parent unit may be set too low or may be

switched off. Turn the volume wheel to a higher volume level.

Perhaps you have switched on the automatic screen activation. If the

automatic screen activation is activated, the video display only

switches on when the baby unit picks up a sound. As long as no

sound is detected, the video display is off to save power.

Why does the parent

unit react too quickly to

other sounds?

The baby unit also picks up other sounds than those of your

baby. Move the baby unit closer to the baby (but observe the

minimum distance of 1 metre/3 feet).

 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips-Avent SCD600 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info