Bedienungsanleitung Philips BDL4335QL (Seite 5 von 46) (Englisch)

668469

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

BDL4335QL

Polish Center for Testing and Certication

Notice

The equipment should draw power from a socket with an attached

protection circuit (a three-prong socket). All equipment that works

together (computer, display, printer, and so on) should have the same

power supply source.

The phasing conductor of the room’s electrical installation should have

a reserve short-circuit protection device in the form of a fuse with a

nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must

be removed from the power supply socket, which should be located

near the equipment and easily accessible.

A protection mark “B” conrms that the equipment is in compliance

with the protection usage requirements of standards PN-93/T-42107

and PN-89/E-06251.

Electric, Magnetic and Electronmagnetic

Fields (“EMF”)

1. We manufacture and sell many products targeted at consumers,

which, like any electronic apparatus, in general have the ability to

emit and receive electromagnetic signals.

2. One of our leading Business Principles is to take all necessary health

and safety measures for our products, to comply with all applicable

legal requirements and to stay well within the EMF standards

applicable at the time of producing the products.

3. We are committed to develop, produce and market products that

cause no adverse health effects.

4. We conrm that if its products are handled properly for their

intended use, they are safe to use according to scientic evidence

available today.

5. We play an active role in the development of international EMF and

safety standards, enabling us to anticipate further developments in

standardization for early integration in its products.

Information for U.K. only

WARNING – THIS APPLIANCE MUST BE EARTHED.

Important:

(A)

(B)

This apparatus is supplied with an approved moulded 13A plug. To

change a fuse in this type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved

type.

3. Ret the fuse cover.

If the tted plug is not suitable for your socket outlets, it should be cut

off and an appropriate 3-pin plug tted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug

without a fuse is used, the fuse at the distribution board should not be

greater than 5A.

NOTE: The severed plug must be destroyed to avoid a possible shock

hazard should it be inserted into a 13A socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured in accordance with the

following code:

BLUE – “NEUTRAL” (“N”)

BROWN – “LIVE” (“L”)

GREEN & YELLOW – “EARTH” (“E”)

1. The GREEN & YELLOW wire must be connected to the terminal in

the plug which is marked with the letter “E” or by the Earth symbol

or coloured GREEN or GREEN & YELLOW.

2. The BLUE wire must be connected to the terminal which is marked

with the letter “N” or coloured BLACK.

3. The BROWN wire must be connected to the terminal which

marked with the letter “L” or coloured RED.

Before replacing the plug cover, make certain that the cord grip is

clamped over the sheath of the lead – not simply over the three wires.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips BDL4335QL Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips BDL4335QL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info