1047
96
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
88
a The following message appears on the screen: 'Please enter
programme number'
b The programme number of the TV channel has not yet been assigned to
the ShowView number. Use C , D or the number buttons 0..9 on the
remote control to select the appropriate programme number (name) of the
TV channel and confirm with OK .
a The following message appears on the screen: 'ShowView number
wrong'
b The entered ShowView number is incorrect. Correct your entry or cancel
using the SYSTEM-MENU button.
b Check the time/date (see 'Setting the time & date' in 'Installing your DVD
recorder').
a The following message appears on the screen: 'Weekend
programming not possible'
b A daily recording was entered for the wrong day. Daily programming can
only be used for recordings to be made from Monday to Friday.
Problem
Timer
ShowView system
Date
01
Prog.
BBC1
Start
20:15
VPS
PDC End
21:30
Rec
Mode
M2
Mo-Fr/Weekly
Press SELECT
To store
Press OK
6 The decoded data appears after confirmation. You can go back and
change the data. Select the appropriate input field with C or D .If
required, make changes using A , B or the number buttons 0..9 .
'Switching on 'VPS/PDC' in the 'Start' input field
Select the 'Start' input field using C . Using SELECT switch on 'VPS/PDC'
('*' lights up). If you press SELECT again, you will switch 'VPS/PDC' off ('*'
goes out).
Changing the recording mode in input field 'End'
Select the 'End' input field using C .
Use REC MODE to select the recording mode 'M1, M2, M2x, M3, M4, M6,
M8'.
Fit to space Recording
You can select also the recording mode 'FR'.
With these setting the recording mode (bit rate) will be automatically
calculated to use the complete empty space (title 'Empty').
If the empty space is too small the recording will be stopped to prevent the
following titles from being overwritten.
Do not use this function under the following conditions:
•) more then one programmed recording
•) daily/weekly repeated recordings
•) recordings with VPS/PDC
May be the calculation of the recording mode can not function properly.
Tip
7 If all information is correct, press the OK button. The programming
information is stored in a TIMER block.
8 To end, press TIMER s .
9 Insert a recordable disc (one without write protection).
The inserted disk is checked.
0 Search the position on the disc where the recording should begin.
Press STOP h .
A Switch the DVD recorder off with STANDBY m .
The programmed recording will only function properly if the DVD
recorder has been switched off using the STANDBY m button.
If any of the TIMER blocks are in use, 'TIMER' will light up on the recorder display.
Programming a recording (TIMER)
96

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Philips DVDR77 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Philips DVDR77

Philips DVDR77 Bedienungsanleitung - Deutsch - 123 seiten

Philips DVDR77 Bedienungsanleitung - Holländisch - 120 seiten

Philips DVDR77 Bedienungsanleitung - Französisch - 128 seiten

Philips DVDR77 Bedienungsanleitung - Spanisch - 122 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info