Bedienungsanleitung Philips EP 4324 (Seite 16 von 242) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

811364

Zoom out

Zoom in

Vorherige Seite

1/242

Nächste Seite

Activating the AquaClean water filter (5 min.)

The machine does not automatically detect that a filter has been placed in the water tank.

Therefore you need to activate each new AquaClean water filter that you install in the 'Clean' menu.

When the machine stops showing the filter activation message, you can still activate an AquaClean

water filter, but you will need to descale the machine first.

Your machine has to be completely limescale-free before you start using the AquaClean water

filter.

Before activating the AquaClean water filter, it has to be prepared by soaking it in water as described

below. If you don't do this, air might be drawn into the machine instead of water, which makes a lot of

noise and prevents the machine from being able to brew coffee.

1Tap the 'Clean' icon and use the up and down arrows to select 'AquaClean'.

2Tap the OK icon to confirm.

3Tap the OK icon again when the activation screen appears. Follow the instructions on the screen.

4Shake the filter for about 5 seconds (Fig. 45).

5Immerse the filter upside down in a jug with cold water and shake/press it (Fig. 46).

6Insert the filter vertically onto the filter connection in the water tank. Press it down to the lowest

possible point (Fig. 47).

7Fill the water tank with fresh water and place it back into the machine.

8If attached, remove the LatteGo (specific types only).

9Place a bowl under the hot water spout/milk frother.

10 Press the start/stop button to start the activation process.

11 Hot water will be dispensed from the hot water spout/milk frother during 1 minute.

12 The filter is now successfully activated.

Replacing the AquaClean water filter (5 min.)

After 95 liters of water have flowed through the filter, the filter will cease to work. The AquaClean

status indicator drops to 0% to remind you to replace the filter. As long as the AquaClean status

indicator is shown on the display you can replace the filter without having to descale the machine first.

If you do not replace the AquaClean water filter in time, the AquaClean indicator goes out after some

time. In that case you can still replace the filter but you first need to descale the machine.

When the AquaClean status indicator drops to 0% or when the machine reminds you to replace the

AquaClean filter:

1take out the old AquaClean water filter.

2install a new filter and activate it as described in chapter 'Activating the AquaClean water filter (5

min.)'.

Replace the AquaClean water filter at least every 3 months, even if the machine does not yet

indicate that replacement is required.

Descaling procedure (30 min.)

Please use Philips descaler only. Under no circumstances should you use a descaler based on sulfuric

acid, hydrochloric acid, sulfamic or acetic acid (vinegar) as this may damage the water circuit in your

machine and not dissolve the limescale properly. Not using the Philips descaler will void your

warranty. Failure to descale the appliance will also void your warranty. You can buy Philips descaling

solution in the online shop at www.philips.com/coffee-care.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips EP 4324 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info