Bedienungsanleitung Philips EP3241 (Seite 15 von 264) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

684440

Zoom out

Zoom in

Vorherige Seite

1/264

Nächste Seite

3 The filter is now prepared for use and can be inserted into the water tank.

4 Insert the filter vertically onto the filter connection in the water tank. Press it down to the lowest

possible point (Fig. 40).

5 Fill the water tank with fresh water and place it back into the machine.

6 If attached, remove the LatteGo.

7 Place a bowl under the hot water spout/milk frother.

8 Press the AquaClean icon for 3 seconds (Fig. 41). The start light starts to pulse.

9 Press the start/stop

button to start the activation process.

10 Hot water will be dispensed from the hot water spout/milk frother (3 min.).

11 When the activation process is finished, the blue AquaClean light goes on to confirm that the

AquaClean water filter has been activated correctly.

Replacing the AquaClean water filter (5 min.)

After 95 liters of water have flowed through the filter, the filter will cease to work. The AquaClean light

turns orange and starts to flash to remind you to replace the filter. As long as it flashes, you can

replace the filter without having to descale the machine first. If you do not replace the AquaClean

water filter, the orange light will go out eventually. In that case you can still replace the filter but you

first need to descale the machine.

When the orange AquaClean light flashes:

1 Take out the old AquaClean water filter.

2 Install a new filter and activate it as described in chapter 'Activating the AquaClean water filter (5

min.)'.

Replace the AquaClean water filter at least every 3 months, even if the machine does not yet

indicate that replacement is required.

Deactivating the AquaClean reminder

If you do not want to use Philips AquaClean water filters anymore, you can always deactivate the

AquaClean reminders:

1 Press the on/off button to switch off the machine.

2 When the machine is switched off, press and hold the AquaClean icon until the light in this icon

goes on. The start light starts flashing.

3 Tap the AquaClean icon again to deactivate the reminders. The light in the AquaClean icon goes

off.

4 Press the start/stop button to confirm your choice.

5 Press the on/off button to switch on the machine again. The AquaClean reminders are now

deactivated.

Note: The activation of a new AquaClean filter will automatically re-activate the AquaClean reminders.

Setting the water hardness

We advise you to adjust the water hardness to the water hardness in your region for optimal

performance and a longer lifetime of the machine. This also prevents you from having to descale the

machine too often. The default water hardness setting is 4: hard water.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips EP3241 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips EP3241

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info