Bedienungsanleitung Philips FC8796 Robot SmartPro Easy (Seite 7 von 86) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

673173

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

or rug, please stay close by the first time to see if the robot can deal with this type of floor. The robot

also needs supervision when you use it on very dark or shiny hard floors.

How your robot cleans

Cleaning system

The robot has a 3-stage cleaning system to clean your floors efficiently.

The two side brushes help the robot clean in corners and along walls. They also help to remove dirt

from the floor and move it towards the suction opening (Fig. 3).

The suction power of the robot picks up loose dirt and transports it through the suction opening

into the dust container (Fig. 4).

Types FC8796 and FC8794 come with a mopping attachment that can be attached to the robot to

mop your hard floor.

Cleaning patterns

In its auto cleaning mode, the robot uses an automatic sequence of cleaning patterns to clean each

area of the room optimally. The cleaning patterns it uses are:

1 Random pattern (Fig. 5)

2 Wall-following pattern (Fig. 6)

3 Spot-cleaning pattern (Fig. 7)

In its auto cleaning mode, the robot uses these patterns in a fixed sequence: random pattern, wall-

following pattern, and spot-cleaning pattern.

When the robot has completed this sequence of patterns, it starts moving in random pattern again.

The robot continues to use this sequence of patterns to clean the room until the rechargeable battery

runs low, or until it is switched off manually.

Note: You can also select each mode individually by pressing the appropriate button on the remote

control (see 'Cleaning mode selection'). The robot continues cleaning in the selected cleaning mode

until you switch the robot off and on again.

How your robot avoids height differences

The robot has five drop-off sensors in its bottom. It uses these drop-off sensors to detect and avoid

height differences such as staircases.

Note: It is normal for the robot to move slightly over the edge of a height difference, as its front drop-

off sensor is located behind the bumper.

Caution: In some cases, the drop-off sensors may not detect a staircase or other height difference

in time. Therefore monitor the robot carefully the first few times you use it, and when you operate it

near a staircase or another height difference. It is important that you clean the drop-off sensors

regularly to ensure the robot continues to detect height differences properly (see 'Cleaning the

robot').

Before first use

Mounting the side brushes

1 Unpack the side brushes and place the robot upside down on a table or on the floor.

2 Push the side brushes onto the shafts on the bottom of the robot (Fig. 8).

Note: Make sure you attach the side brushes properly. Press them onto the shaft until you hear

them lock into position with a click.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips FC8796 Robot SmartPro Easy Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips FC8796 Robot SmartPro Easy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info