Bedienungsanleitung Philips FC8796 Robot SmartPro Easy (Seite 10 von 86) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

673173

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

Mopping with the robot

Types FC8796 and FC8794 come with a mopping attachment and a mopping pad for wet cleaning of

hard floors.

Attaching the mopping pad

1 Soak the mopping pad in water or wet the mopping pad under the tap. You can add a few drops of

a readily available floor cleaner that is suitable for your floor.

2 Squeeze the mopping pad thoroughly to ensure it is only damp instead of wet.

3 Attach the damp mopping pad to the mopping attachment by pushing the Velcro fasteners of the

mopping pad onto Velcro fasteners of the mopping attachment (Fig. 29).

4 Insert the attachment lugs of the mopping attachment into the two attachment holes located just

behind the wheels. Then press down until you hear a click (Fig. 30).

Cleaning floors with the mopping attachment

Note: To clean hard floors with the mopping attachment, you have to start the robot from a point in

the room you wish to clean. You cannot start the robot from its docking station with the mopping pad

attached.

1 Just press the start/stop button on the remote control to start the robot.

The robot continues mopping until its battery runs low and the robot stops.

Note: Detach the mopping pad and the mopping attachment before you send the robot to the

docking station with the docking button on the remote control or before you place the robot on the

docking station manually.

Detaching the mopping attachment

1 To detach the mopping attachment, press the tab (1) and pull up the mopping attachment to

remove it (2) (Fig. 31).

2 Pull the mopping pad off the mopping attachment.

3 To clean the mopping pad, wash it in the washing machine on a gentle cycle at a temperature of

60°C max.

Alarm signal

If the robot gets into trouble while cleaning (e.g., because a wheel jams or is no longer in contact with

the floor, or because a sensor can no longer detect the floor), you will hear a sound and the robot

stops. Press the start/stop button to switch the robot to standby mode and solve the problem that

causes the alarm signal, for instance by removing the obstacle that blocks the wheel, cleaning the

sensors, or picking up the robot and putting it down in a different place.

Cleaning and maintenance

Emptying and cleaning the dust container

Empty and clean the dust container when the dust container is full.

1 Pull up the handle of the dust container lid and lift the dust container out of the dust container

compartment (Fig. 32).

2 Pull the tab on the side of the dust container to open the lid (Fig. 33).

3 Remove the filter unit from the dust container (Fig. 34).

4 Shake the dust container over a dustbin to empty it (Fig. 35).

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips FC8796 Robot SmartPro Easy Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips FC8796 Robot SmartPro Easy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info