Bedienungsanleitung Philips GC6340 (Seite 9 von 120) (Holländisch)

60514

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

When you steam iron woollen fabrics, shiny patches may occur. To prevent this, use a dry

pressing cloth or turn the article inside out and iron the reverse side.

Iron velvet and other fabrics that tend to acquire shiny patches in one direction only (along with

the nap) while you apply very little pressure.

Do not use steam when you iron coloured silk. This could cause stains.

Using the appliance

Steam ironing

Never direct the steam at people.

Steam ironing is only possible at higher ironing temperatures (temperature settings

2 to

MAX).

1 Make sure that there is enough water in the steam tank.

2 Select an ironing temperature between 2 and MAX.

3 Select a steam setting suitable for the selected ironing temperature: (Fig. 8)

Select a low to medium steam setting for temperature setting

Select a medium to MAX steam setting for temperature settings

3 to MAX.

Note: You cannot use the steam function at temperature setting

4 Put the mains plug in an earthed wall socket and set both the steam tank switch and the iron

switch to ‘on’.

The steam tank and iron power-on lights go on. The temperature light on the iron also goes

on.

The steam tank and the soleplate start to heat up.

Cold start: the soleplate takes approximately 2 minutes to heat up and the steam tank takes

approximately 8 minutes to heat up.

Quick reheat: if you rell the steam tank during ironing, the water in the steam tank takes

approximately 6 minutes to heat up.

5 As soon as the water in the steam tank is hot enough for steam ironing, the steam tank

power-on light goes out. The steam-ready light goes on (GC6360 only).

The appliance is now ready for steam ironing.

6 Keep the steam activator pressed in while you steam iron. (Fig. 5)

Note: During steam ironing, the steam-ready light goes on from time to time. This indicates that the

steam tank is heating up to the right temperature.

Note: If you have not used the steam function for some time, the steam that was still present in the

supply hose will have condensed into water. When you start to steam iron again, this can cause some

spluttering in the appliance and some water droplets to escape from the soleplate.

Note: To prevent droplets from falling onto your garments, hold the iron over an old cloth. Press the steam

activator until the steam production has normalised before you start to steam iron again.



Do not press the steam activator while you iron.

1 Set the required ironing temperature (see chapter ‘Preparing for use’, section ‘Setting the

temperature’).

2 Put the mains plug in an earthed wall socket and set the iron switch to ‘on’.

The soleplate starts to heat up.

ENGLISH 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips GC6340 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips GC6340

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info