Bedienungsanleitung Philips hd 4690 (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

375201

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Depending on the hardness of the water in your area, small spots may appear on the heating

element of your kettle when you use it. This phenomenon is the result of scale build-up on

the heating element and on the inside of the kettle over time. The harder the water, the

faster scale will build up. Scale can occur in different colours. Although scale is harmless, too

much scale can inuence the performance of your kettle. Descale your kettle regularly by

following the instructions given in the chapter ‘Descaling’.



This Philips appliance complies with all standards regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this user manual, the appliance is safe to use based on

scientic evidence available today.

Boil-dry protection

This kettle is equipped with boil-dry protection. This device will automatically switch the kettle off if

it is accidentally switched on when there is no water or not enough water in it. The on/off switch

will stay in ‘on’ position, but the power-on light ring will go out. Set the on/off switch to ‘off’ and let

the kettle cool down for 10 minutes. Then lift the kettle from its base to reset the boil-dry

protection. The kettle is now ready for use again.



Remove stickers, if any, from the base or kettle.

2 Place the base on a dry, stable and at surface.

3 You can adjust the length of the cord by turning the cord winder clockwise to make it

shorter or anticlockwise to make it longer (Fig. 2).

Before using the kettle for the rst time:

4 Rinse the kettle with water.

5 Fill the kettle with water up to the maximum level and let it boil once (see ‘Using the

appliance’).

6 Pour out the hot water and rinse the kettle once more.

Using the appliance

Open the lid by pressing the lid release button (Fig. 3).

2 Fill the kettle with water (Fig. 4).

You can ll the kettle either through the spout or through the open lid.

3 Close the lid.

Make sure that the lid is properly closed to prevent the kettle from boiling dry.

4 Place the kettle on its base.

5 Put the plug in the wall socket.

6 Set the on/off switch to ‘on’ (Fig. 5).

The power-on light ring goes on and the kettle starts heating up.

The kettle switches off automatically when the water has reached boiling point. You will hear

a bell and the light ring goes out.

Cleaning and descaling

Always unplug the appliance before cleaning it.

Do not use any abrasive cleaning agents, scourers etc. to clean the kettle.

ENGLISH 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips hd 4690 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info