Bedienungsanleitung Philips HDRW720 (Seite 104 von 115) (Englisch)

35638

104

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

101

PROBLEM/HINTS SOLUTION

The wrong TV channel

was decoded

(recorded) after you

programmed a

recording using

ShowView System.

bThe programme number of the TV channel is not available in the GUIDE Plus+

system or allocation is

wrong.

To change or check the channel data, proceed as follows:

1 Press GUIDE/TV J .

2 Press A I .

3 Select 'Editor' with C M .

4 Select the TV channel using B O or A I .

5 Press C M to go to the right tile.

In case you can receive the selected channel only via an external receiver, press the red

button to select the corresponding source.

6 Press the green button.

7 Enter the programme number of the TV channel using the number buttons.

If the source you have selected is an external receiver, enter the programme number that you

would also enter at the external receiver for this TV channel.

8 Confirm with OK L .

bIf no GUIDE Plus+

data is available, enter the right programme number after you have confirmed the

ShowView programme number using OK

L .

TV channels will be

deactivated in the

GUIDE Plus+

System

after 24 hours

bThis happens occasionally. To switch on the channels proceed as follows:

1 Press GUIDE/TV J .

2 Press A I .

3 Select 'Editor' using C M .

4 Select the TV channel using B O or A I .

5 Press D K to select the left row.

6 Switch on the TV channel using the red function button D .

7 End with GUIDE/TV J .

No 'VPS/PDC time' in

the GUIDE Plus+

System

bThe GUIDE Plus+

System just shows the start time. The 'VPS/PDC' time will be taken into account.

There is no channel

overview in the GUIDE

Plus+

system

bDVD recorder is switched on: Switch off the DVD recorder to allow data transfer

bThe TV channel that transmits the GUIDE Plus+

data is not set properly.

bExternal receiver (satellite receiver, set-top box, cable TV box, ...) (if available) is switched off: switch on the

external receiver

bG-LINK cable is not connected: Connect the G-LINK cable and make the necessary settings to control the

external receiver (see chapter 'The GUIDE Plus+

System', section 'Installation of the 'External receiver

1').

bCheck that your external receiver (if available) sends out teletext data through the scartcable.

Connect therefore the scartcable from the external receiver directly to the TV set and call up the teletext

function on the TV set from a TV channel that transmits teletext data. If no teletext appears, your external

receiver can not be used for the GUIDE Plus+

system.

Missing or wrong TV

channel in the 'Grid'

screen

bWrong local post code/country was entered

bPlease check your correct channel line up in the 'Grid' screen.

Read therefore the section 'The 'Editor' screen.

When you press

GUIDE/TV

J the

GUIDE Plus+

setup

screen will appear

bThe GUIDE Plus+

system was not completely installed or local post code was not entered.

1 Check the settings

2 Select the corresponding line using B O or A I and confirm with OK L .

3 For more information on the individual functions, see chapter 'The GUIDE Plus+

system',

section 'Setting up the GUIDE Plus+

System'.

Before you call an engineer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips HDRW720 Seite 104

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips HDRW720

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info