Bedienungsanleitung Philips HF3470 (Seite 9 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Finnisch)

461878

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

4 Press the menu + or - button to change a setting. (Fig. 9)

5 Press the SELECT button to conrm (Fig. 10).

Using the lamp

You can use the appliance as a bedside lamp.

1 To switch on the lamp, press the lamp on/off button. (Fig. 11)

2 Press the light intensity + and - buttons to select a light intensity (Fig. 12).

You can choose a light intensity between 1 and 20.

Note: It takes approx. 1 second for the lamp to go on. This is normal, the lamp needs to heat up.

Note: The light intensity you have selected is automatically set as the light intensity level for the alarm as

well.

Tip: When you use the appliance for the rst time, set the light intensity to 20. The moment you wake up,

check which light intensity level the appliance has reached by briey pressing the light intensity + or -

button. When you do this, the current alarm light intensity level appears on the display. Set the alarm light

intensity to this level for the next day.

3 To switch off the lamp, press the lamp on/off button again.

Setting the alarm

When you set the alarm, you choose an alarm time and (only in case of HF3470) the type of sound

you want to wake up to. The alarm is set when the alarm symbol is visible on the display. The light

intensity slowly increases to the selected level during the last 30 minutes before the set alarm time.

The sound slowly increases in 90 seconds to the selected level after the set alarm time.

Note: You can set the light intensity by pressing the light on/off button and then pressing the light intensity

+ or - button and you can set the alarm volume by pressing the volume increase or decrease button. If

you do not want to wake up to the lamp or to a sound, select a light intensity or volume level of OFF. See

sections ‘Using the lamp’ and ‘Radio/Volume’ in this chapter.

1 Push the control lever down to the middle position to switch on the alarm. (Fig. 13)

, The hour indication of the alarm time ashes (Fig. 14).

, To adjust the time, follow steps 2 to 5. If the alarm time is correct, just wait a few seconds.

2 Press the menu + or - buttons to select the hour (Fig. 9).

Note: You can only do this when the hour indication ashes. If this is not the case, push the control lever

up and down again to enter the alarm time mode. You can also set the alarm time in the menu. See

section ‘Menu functions’ in this chapter.

3 Press the SELECT button to conrm (Fig. 10).

, The minute indication of the alarm time starts to ash (Fig. 15).

4 Press the menu + and - buttons to select the minutes. (Fig. 9)

5 Press the SELECT button to conrm or wait for a few seconds (Fig. 10).

, The appliance leaves the menu and the display shows the clock time.

The alarm time is now set.

Switching off the alarm

To switch off the alarm function, push up the control lever to the top position.

Note: The lamp stays on to light your room. You can switch off the lamp by pressing the light on/off

button.

Note: The alarm (sound and/or light) automatically switches off after 90 minutes.

ENGLISH 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips HF3470 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info