Bedienungsanleitung Philips HI 5916 (Seite 6 von 46) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

696521

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

English

2 Place the Calc-Clean container on the ironing board or any other even, stable surface.

3 Place the iron stably on the Calc-Clean container (Fig. 5).

Note: The Calc-Clean container has been designed to collect scale particles and hot water during

the Calc-Clean process. It is perfectly safe to rest the iron on this container during the entire

process.

4 Press and hold the Calc-Clean button for 2 seconds until you hear short beeps (Fig. 6).

5 During the Calc-Clean process, you hear short beeps and a pumping sound (Fig. 7).

6 When the Calc-Clean process is completed, the iron stops beeping and the CALC-CLEAN light

stops ashing (Fig. 8).

7 Wipe the iron with a piece of cloth and put it back on the base station (Fig. 9).

8 As the Calc-Clean container becomes hot during the Calc-Clean process, wait approx. 5 minutes

before you touch it. Then carry the Calc-Clean container to the sink, empty it and store it for future

use (Fig. 10).

9 If necessary, you can repeat steps 1 to 7. Make sure that you empty the Calc-Clean container before

you start the Calc-Clean process.

Note: During the Calc-Clean process, clean water may come out of the soleplate if no scale has

accumulated inside the iron. This is normal.

Troubleshooting

This chapter summarizes the most common problems you could encounter with the appliance. If you

are unable to solve the problem with the information below, visit www.philips.com/support for a list

of frequently asked questions or contact the Consumer Care Center in your country.

Problem Possible cause Solution

The iron does not

produce any steam.

You have set the

temperature dial to SYNTH

to 1.

Turn the temperature dial to 2 or higher.

The steam function has

been disabled until you

have performed the Calc-

Clean process.

Perform the Calc-Clean process to restore

the steam function (see chapter ‘Cleaning

and maintenance’).

At the start of your ironing

session, the steam trigger

has not been pressed long

enough.

Press and hold the steam trigger until

steam comes out. It may take up to 30

seconds until steam comes out.

The Calc-Clean light

ashes. No steam comes

out of the soleplate and/

or the appliance beeps.

You have not done or have

not completed the Calc-

Clean process.

Perform the Calc-Clean process to enable

the steam function again (see chapter

‘Cleaning and maintenance’).

The appliance has

switched o.

The auto shut-o function

is activated automatically

when the appliance has not

been used for more than 5

minutes.

To activate the appliance again, set the on/

o switch to ‘o’ position and then to ‘on’

position. The appliance then starts to heat

up again.

The appliance produces

a loud pumping sound.

The water tank is empty. Fill the water tank with water and press

the steam trigger until the pumping sound

becomes softer and steam comes out of

the soleplate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips HI 5916 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info