Bedienungsanleitung Philips hp 6315 (Seite 4 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

370094

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

English

Your Ladyshave (fig. 1)

• The shaver head Aconsists of a shaver foil which leaves

your skin really smooth and two trimmers for the longer

hairs.

Protect the Ladyshave by putting the protective cap back

after each use.

• Use the small brush Bto clean the Ladyshave after each

use.

•A voltage selector C is situated at the back of the

Ladyshave. Use a coin to turn the voltage selector. When

set to position “115” you can connect your Ladyshave to an

electric mains of 110-120 V (alternating current = 50 Hz)

and when set to position “230” to an electric mains of

220-240 V (alternating current = 50 Hz).

Pay attention to this when taking your Ladyshave along on

a journey.

• Connect your Ladyshave to the electric mains with the

cord D. Push the cord into the appliance as far as the line

on the plug.

• Switch the Ladyshave on and off with the switch E.

Shaving (fig. 2-5)

Ensure your skin is clean and in particular completely dry

before shaving. (If you have sensitive skin, apply a light

dusting of talc before shaving.)

Stretch the skin taut between two fingers so that the hairs

stand up, and put the Ladyshave gently on the skin. Move

the Ladyshave slowly and at an angle to the hair growth.

After each use: always clean (fig. 6-8)

Your Ladyshave will have a considerably longer life if you

clean it after each use. This is done as follows:

- Switch the Ladyshave off.

- Remove the shaver head (fig. 6). Tap it out and blow it

clean. Use the small brush to remove hairs from the

Ladyshave (fig. 7).

- Put the shaver head back onto the Ladyshave (fig. 8). Do

not press on the shaver foil when placing the shaver head.

- Put the protective cap back onto the shaver again to

prevent the shaver head from being damaged.

One or two times a year (fig. 9-12)

Spend some time on maintenance once or twice per year.

Remove the shaver head from the Ladyshave and clean it

with alcohol or Philips Shaver Cleaner.

Then rub a drop of sewing machine oil into each trimmer and

into the shaver foil with your finger (fig. 9).

The shaver head can be replaced if defective.

A replacement shaver head is available from your dealer

under type number HP 2901.

Cleaning the inside of the shaver head

Note: Never apply pressure on the shaver foil.

Handle the shaver foil holder precisely as indicated in the

figures.

- Fig 10 Hold the shaver head over a flat surface (e.g. table

top). Position the end of the brush on the side of the shaver

head as indicated.

- Fig. 11 Lever the brush as indicated by the arrow. When

doing so, you loosen the shaver foil holder. You can now

brush the inside of the shaver head.

- Fig. 12 After cleaning place the shaver foil holder on a

clean, smooth surface, with the shaver foil facing

downwards. (The shaver foil will not touch the surface as

the shaver foil holder will rest on the rims.) Hold the part

containing the trimmers as illustrated and press it home

firmly (“Click!”).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips hp 6315 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info