Bedienungsanleitung Philips hp8550 01 (Seite 15 von 204) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

368481

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

Storage

Let the appliance cool down for 15 minutes before you put it in transport position and store

it.

2 Store the protective goggles in the storage compartment between the two lamps. (Fig. 38)

3 Put the remote control and the cord in the pouch on the back of the control panel (HP8565

only). (Fig. 39)

4 Make sure the cord does not get stuck between parts of the appliance when you put the

appliance in transport position.

5 Turn the appliance away from the bed or sofa and make sure there is enough space around

the appliance to collapse it.

6 Press the two release buttons in the recesses of the control panel and slide the control panel

down the stand as far as it goes. (Fig. 40)

7 Turn the lamp unit in the direction of the arrow. (Fig. 41)

You hear a click when the lamp unit locks in vertical position.

8 Pull the stand slightly backwards and then press the dual push button. Lower the stand slowly

until the lamp unit rests on the oor between the legs. (Fig. 42)

9 Wind the cord and fasten it with the Velcro cord wrap strip. (Fig. 43)

You can store the appliance in a wardrobe or under a bed.

Replacement

Tanning lamps

Have the Philips tanning lamps (Cleo HPA Synergy) replaced by a service centre authorised by

Philips. Only they have the knowledge and skills required for this job and the original spare parts

for the appliance.

The light that the tanning lamps emit becomes less bright in time (i.e. after a few years in case of

normal use). When this happens, you notice a decrease in the tanning capacity of the appliance.

After 750 operating hours, the tanning capacity of the lamps has decreased so much that

replacement of the tanning lamps is advisable.

HP8565/HP8560: the appliance has a counter that records the operating hours of the tanning

lamps. After 750 operating hours, an L appears on the left-hand side of the display to indicate

that replacement of the tanning lamps is advisable (Fig. 44).

Note: Of course, you can choose to postpone replacement for a while by setting a longer tanning time.

Viewing the operating hours of the tanning lamps

1 Set the time to 00 and press the repeat button ( ä) at least 2 seconds to make the

operating hours appear on the display. The maximum number of hours that can be displayed

is 999. When this value has been reached, the counter starts to count up from 000 again.

Note: The operating hours disappear from the display as soon as you release the repeat button (

ä).

HP8565/HP8560: removing the L from display

To remove the L from the display:

1 Make sure time indicated on the display is 00.

2 Press and hold down the START/STOP button.

3 Press and release the repeat button ( ä).

ENGLISH 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips hp8550 01 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info