Bedienungsanleitung Philips hr2939 blender (Seite 2 von 3) (Englisch)

381126

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

ENGLISH

Introduction

The chopper is intended for chopping ingredients such

as onions, meat, herbs, vegetables, fruit, chocolate, rm

cheese, baby food and nuts.

The chopper is suitable for Philips blender types:

HR2074

HR2071

HR2069

HR2067

HR2066

HR2064

HR2063

HR2061

General description (Fig. 1)

A Lid

B Blade unit

C Chopper bowl

D Coupling unit

Important

Read this user manual carefully before you use the

chopper and save it for future reference.

To use the blender motor unit, follow the instructions in

the user manual of the blender.

Warning

Do not use the chopper if it is damaged.

Do not touch the blades, especially when the

chopper is connected to the blender motor unit. The

blades are very sharp.

Make sure the coupling unit is securely fastened

to the chopper bowl before you assemble the

chopper onto the motor unit.

Never reach into the chopper bowl with your ngers

or an object while the chopper is operating.

The chopper is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the chopper by a

person responsible for their safety.

Children should be supervised to ensure that they

do not play with the chopper.

Never let the chopper operate unattended.

If the blades get stuck, unplug the blender motor unit

before you remove the ingredients that block the

blades.

Never use the chopper bowl to switch the motor

unit of the blender on and off.

Caution

Always unplug the blender motor unit before you

assemble, disassemble or make adjustments to any

of the parts.

Never use any accessories or parts from other

manufacturers or that Philips does not specically

recommend. If you use such accessories or parts,

your guarantee becomes invalid.

Do not exceed the maximum quantities indicated in

the table.

If food sticks to the wall of the chopper bowl, switch

off the blender motor unit and unplug it. Then use a

spatula to remove the food from the wall.

Always make sure the lid is properly assembled on

the chopper bowl before you switch on the blender

motor unit.

Never ll the chopper bowl with ingredients hotter

than 80ºC.

Do not use the chopper to mix liquids. Use the

blender jar instead.

Never immerse the coupling unit in water or any

other liquid.

The gearwheels inside the coupling unit have been

lubricated. Do not lubricate them again.

Before first use

Thorougly clean the parts that come into contact with

food before you use the chopper for the rst time (see

chapter ‘Cleaning’).

Using the appliance

Be careful when you place or remove the blade unit: the

cutting edges of the blade are very sharp.

1 Insert the coupling unit into the bottom of the

chopper bowl (1) and turn it anticlockwise to x it

(2) (Fig. 2).

2 Place the chopper bowl (1) on the blender motor

unit and turn it clockwise to x it (2). (Fig. 3)

3 Place the blade unit in the chopper bowl (Fig. 4).

4 Put the ingredients in the chopper bowl (Fig. 5).

See the table below for the recommended quantities.

Do not exceed the maximum quantities indicated in

the table.

Maximum quantities

Ingredients Max. quantities

Onions 50-150g

Meat (lean, uncooked) 50-200g

Herbs (e.g. parsley) 10-20g

Vegetables/fruit (uncooked) 75-150g

Chocolate 50-75g

Cheese (rm, crustless) 50-100g

Baby food 100-200g

Nuts (shelled) 25-150g

Tip: Precut large pieces of food into pieces of 1-2cm.

5 Put the lid on the chopper bowl (1) and turn it

clockwise to x it (2) (Fig. 6).

Note: Make sure the lid is properly xed before you switch

on the blender motor unit.

6 Switch on the blender motor unit.

Note: If the appliance shakes because the food is not evenly

distributed, put your hand on the lid.

Note: The chopper does its work in a few seconds. Never let

it run longer than a few seconds.

7 When you have nished chopping, switch off the

blender motor unit and unplug it.

8 Turn the chopper anticlockwise (1) and remove it

from the blender motor unit (2). (Fig. 7)

Always remove the chopper from the motor unit

before you empty the chopper bowl.

9 Turn the coupling unit clockwise (1) and remove it

from the bottom of the chopper bowl (2) (Fig. 8).

10 Remove the lid and the blade unit from the

chopper bowl.

11 Empty the chopper bowl.

Cleaning

Always unplug the blender motor unit before you clean

the chopper.

Never use scouring pads, abrasive cleaning agents or

aggressive liquids such as petrol or acetone to clean the

chopper.

1 Disassemble the chopper.

2 Clean the coupling unit with a moist cloth.

Never immerse the coupling unit in water or any other

liquid. Do not clean the coupling unit in the dishwasher.

3 Clean the chopper bowl, the lid and the blade unit

in warm water with some washing-up liquid.

Note: You can also clean these parts in the dishwasher.

Environment

Do not throw away the appliance with the normal

household waste at the end of its life, but hand it in

at an ofcial collection point for recycling. By doing

this, you help to preserve the environment (Fig. 9).

Guarantee & service

If you need information or if you have a problem, please

visit the Philips website at www.philips.com or contact

the Philips Customer Care Centre in your country

(you nd its phone number in the worldwide guarantee

leaet). If there is no Customer Care Centre in your

country, go to your local Philips dealer or contact the

Service Department of Philips Domestic Appliances and

Personal Care BV.

4222.002.3023.2

2/3

Philips hr2939 blender Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips hr2939 blender

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info