Bedienungsanleitung Philips LX7000SA (Seite 14 von 31) (Englisch)

663514

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

English

Setting up the surround sound

system

You must connect all the speakers and set up the system

properly in order to enjoy the Digital Cinema experience at

home (refer to “Connections - Connecting the speakers”).

You will have the feeling of being in the middle of the action

because sound is coming from everywhere around you.

The subwoofer can enhance the bass performance of your

system dramatically.

IMPORTANT!

Please sit at your usual listening position in order

to set up the speaker balance correctly.

Placing the speakers

To obtain the best surround effect, place the speakers as

follows.

1 Place the front left and right speakers at equal distances

from the TV and at an angle of approximately 45 degrees

from the listening position.

2 Place the centre speaker above or below the TV so the

centre channel’s sound is localised.

3 Place the surround speakers at normal listening ear level

facing each other or mounted on the wall.

4 Place the subwoofer on the floor near the TV.

Notes:

– To avoid magnetic interference, do not position the front

speakers too close to your TV.

– If the rear surround speakers are installed farther away

from the listening position than the front and centre speakers,

it will weaken the surround effect.

– All speakers should be securely installed to prevent

accidents and improve sound quality.

Changing the volume level

You can change the speakers’ sound distribution to suit

your surround sound needs, except for CDDA DTS disc.

● Press CENTER +/- to adjust the level of the centre

speaker.

➜ “CEN XX” is displayed.

● Press REAR +/- to adjust the level of the rear

surround speakers.

➜ “SL XX” or “SR XX” is displayed.

Notes:

–“XX” denotes the volume level between -6 to +6.

– For CDDA DTS disc, please refer to “System Setup (DVD) -

Setting the sound ( ) - Speakers” for changing the volume

level of the centre speaker, rear speakers and subwoofer.

Setting up the subwoofer

1 Use the supplied subwoofer cable to connect the

subwoofer’s audio input jack to the WOOFER LINE

OUT jack of the DVD system.

2 Connect the subwoofer’s AC power cable to the wall

socket and switch on the power.

➜ It will automatically switch on when receiving an audio

signal input. If there is no audio signal input, it will switch off

automatically.

3 Set the phase polarity at the rear of the subwoofer at

either 0

or 180

to determine better bass reproduction

effect in your listening environment.

4 Press SUBW +/- to adjust the volume level of the

subwoofer (-6 to +6).

➜ “SUB XX” is displayed.

Inserting batteries into the

remote control

1 Open the battery compartment.

2 Place the batteries in the

compartment with the correct

polarity as indicated by “+“ and “-“

symbols.

3 Close the cover.

CAUTION!

– Remove batteries if they are exhausted or will

not be used for a long time.

– Do not use old and new or different types of

batteries in combination.

– Batteries contain chemical substances, so they

should be disposed off properly.

Preparations

PREPARATIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips LX7000SA Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips LX7000SA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info