Bedienungsanleitung Philips mcd 700 (Seite 30 von 36) (Englisch)

371295

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

English

Radio Reception

Tuning to radio stations

1 Press STANDBY ONy (or y on the remote)

to switch on the last selected source.

2 Press SOURCE (or TUNER on the remote)

to select TUNER mode.

3 Press BAND/9 (or TUNER on the remote)

again to select the desired band: FM or AM.

4 Press and hold the control knob to the left/right

(corresponding to S/T) or TU +/- à /

á on the remote until the frequency indication

starts to change, then release.

➜ The system automatically tunes to the next

strong radio station.

● To tune to a weak station, press the control

knob to the left/right (corresponding to S/

T) or TU +/- à / á on the remote

briefly and repeatedly until an optimal reception

is found.

5 Repeat Step 4 if necessary until you find the

desired radio station.

Presetting radio stations

You can preset up to 40 stations (20 in each

band) regardless of the reception.

1 Tune to your desired radio station (refer to

“Tuning to radio stations”).

2 Press the control knob upward (corresponding

to PROGRAM) or press PROG on the

remote.

➜ ”PROG” icon flashes.

3 Press CH +/- (¡ / ™) or use the Numeric

Keypad (0-9) on the remote to select the

desired preset number.

➜ If “PROG” icon goes off before you select the

desired preset number, press the control knob

upward (corresponding to PROGRAM) or press

PROG on the remote.

4 Press the control knob upward (corresponding

to PROGRAM) or press PROG on the

remote again to store the radio station.

● Repeat steps 1-4 to store other radio stations.

Other Functions

Listening to preset radio stations

● In tuner mode, press PRESET/ÉÅ (or CH

+/- (¡ / ™) on the remote) or use the

Numeric Keypad (0-9) to select the desired

preset number.

➜ The preset number, radio frequency, and

waveband are displayed.

Setting the clock

1 In Standby mode, press and hold CLOCK on

the remote until the time flashes on the display.

➜ ”CLOCK SET” is displayed briefly. Then, the

hour digits flash on the display screen.

2 Turn VOLUME -/+ clockwise or anticlockwise

or press VOLUME +/- on the remote to set

the hours.

3 Press CLOCK to confirm.

➜ The minute digits flash on the display screen.

4 Turn VOLUME -/+ clockwise or anticlockwise

or press VOLUME +/- on the remote to set

the minutes.

5 Press CLOCK again to confirm the clock

setting.

Notes:

– This system only supports 24-hour mode.

– The clock setting will be erased when the

system is disconnected from the power supply.

– The system will exit clock setting mode if no

button is pressed within 30 seconds.

Setting sleep/wake-up timer

Sleep timer setting

In power-on mode, the sleep setting enables

the system to switch to standby mode

automatically at a preset time.

1 In power-on mode, press SLEEP/TIMER on

the remote repeatedly to select a preset time.

➜ The selections are as follows (time in

minutes):

00 ➜ 10 ➜ 20 ➜ 30 ➜ 40 ➜ 50 ➜ 60 ➜ 70

➜ 80 ➜ 90 ➜ 00

2 When you reach the desired length of time,

stop pressing SLEEP/TIMER.

➜ ”SLEEP” appears.

pg001-036_MCD700_37_Eng 2005.7.7, 13:2230

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips mcd 700 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info