Bedienungsanleitung Philips PPX320 PicoPix Micro (Seite 14 von 20) (Englisch)

706807

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

14 Philips · PicoPix Micro

10 Service

Built-in battery care

The capacity of the built-in battery diminishes

with time. You can prolong the life of the

battery if you observe the following points:

• Without a power supply, the projector

operates on the built-in battery. When the

battery does not have sufficient power, the

projector turns off. In this case connect the

projector to the power supply.

• Charge the battery regularly. Don’t store

the projector with a completely discharged

battery.

• If the projector is not used for several

weeks, discharge the battery a little by

using the projector before storing it.

• Keep the projector and the battery away

from sources of heat.

• If the projector cannot be charged after

connecting to the power supply, use a small

pin to press the reset key (a small hole)

located near the USB port of the projector.

Note about deep discharge of battery

When the built-in battery is in deep discharge,

it may take longer for the actual charging

process to start. In this case, charge the

projector for at least five hours before using it.

DANGER!

Risk of explosion with incorrect type

of batteries!

Do not try to replace the built-in

battery yourself.

Cleaning

DANGER!

Instructions for cleaning!

Use a soft, lint-free cloth. Never use

liquid or easily flammable cleansers

(sprays, abrasives, polishes, alcohol,

etc.). Do not allow any moisture to

reach the interior of the projector.

Do not spray the projector with any

cleaning fluids.

Wipe over the surfaces gently. Be

careful that you do not scratch the

surfaces.

Cleaning the lens

Use a soft brush or lens cleaning paper for

cleaning the lens of the projector.

DANGER!

Do not use any liquid cleaning agents!

Do not use any liquid cleaning

agents for cleaning the lens, to avoid

damaging the coating film on the lens.

Update software

The latest software of the projector can be

found on www.philips.com/support for you

to get the best features and support from the

projector.

Before you update the software of the

projector, check the current software version:

• Press , and then navigate to Firmware

Version.

CAUTION!

Do not turn off the projector or remove

the USB flash drive during the update.

Update software through

Internet

1 Connect the projector to the Internet (see

Connect to WiFi network, page 11).

2 Press , and then navigate to select

Firmware Upgrade - Online.

• If an upgrade media is detected, you

are prompted to start or cancel the

update.

3 Follow the on-screen instructions to

complete the update.

Update software through USB

1 Check the latest software version on www.

philips.com/support. Find your product

(model number: PPX320), and locate

‘Software and drivers’.

2 Download the software into the USB flash

drive. Unzip the downloaded software file

and save it in the root directory of the USB

flash drive.

• After unzipping, make sure the folder

is named “PicoPix” and two files of

“config.txt” and “update.img” are

included in the folder.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips PPX320 PicoPix Micro Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips PPX320 PicoPix Micro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info