Bedienungsanleitung Philips qc 5045 (Seite 2 von 9) (Englisch, Holländisch, Türkisch)

401142

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

ENGLISH

Introduction

Congratulations on your purchase and welcome

to Philips! To fully benet from the support that

Philips offers, register your product at www.philips.

com/welcome.

Your new Philips Professional Power hair clipper

enables comfortable clipping of even the toughest

hair. To enjoy using the hair clipper, we advise you

to read the following information.

General description (Fig. 1)

A Cutting element

B Clipping attachment

C On/off slide

D Handle

E Socket for appliance plug

F Large comb

G Small comb

H Setting indications

I Stubble comb

J Setting selector

K Appliance plug

L Adapter

M Cleaning brush

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

Danger

Make sure the adapter does not get wet.

Warning

Check if the voltage indicated on the adapter

and on the appliance corresponds to the

local mains voltage before you connect the

appliance.

The adapter contains a transformer. Do not cut

off the adapter to replace it with another plug,

as this causes a hazardous situation.

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that

they do not play with the appliance.

Remove the clipping attachment from

the handle before you clean the clipping

attachment under the tap.

Caution

Never immerse the handle in water or any

other liquid, nor rinse it under the tap.

Do not use the appliance in the bath or in the

shower.

The clipping attachment of the appliance

complies with the internationally approved IEC

safety regulations and can be safely cleaned

under a tap (Fig. 2).

Use and store the appliance at a temperature

between 15°C and 35°C.

Only use the adapter supplied.

If the adapter is damaged, always have it

replaced with one of the original type in order

to avoid a hazard.

Do not use the appliance when the clipping

attachment or one of the combs is damaged or

broken as this may cause injury.

This appliance is only intended for clipping

human scalp hair. Do not use it for any other

purpose.

Compliance with standards

This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this

user manual, the appliance is safe to use based on

scientic evidence available today.

Using the appliance

Preparing for hair clipping

Only use the appliance on clean, dry hair. Do not

use it on freshly washed hair.

1 Make sure that the head of the person whose

hair you intend to cut is at the same level as

your chest. This ensures that all parts of the

head are clearly visible and within easy reach.

2 Comb the hair in the growth direction (Fig. 3).

Clipping with comb

The appliance comes with three combs for 15

different hair lengths.

The minimum remaining hair length is 1.6mm and

the maximum remaining hair length is 41mm.

1 Select the comb you want to use.

The table shows how long the hair will be after

clipping at the different settings of the small comb

and large comb.

Settings of the small and large comb and

large

Setting Hair length

after clipping

with small

comb

Hair length

after clipping

with large

comb

1 3mm 23mm

2 6mm 26mm

3 9mm 29mm

4 12mm 32mm

5 15mm 35mm

6 18mm 38mm

7 21mm 41mm

Tip: Write down the settings you have used to create

a certain hairstyle as a reminder for future clipping

sessions.

Stubble comb for a ‘stubble look’

To create a ‘stubble look’, clip with the small

comb set to setting 1 (3mm) rst.

Then clip the hair with the stubble comb for a

hair length of 1.6mm.

2 Slide the selected comb into the guiding

grooves on both sides of the handle

(‘click’) (Fig. 4).

3 To set the comb to the desired setting, press

the setting selector (1) and slide the comb to

the desired hair length setting (2) (Fig. 5).

The setting indications on the comb show the

selected setting.

4 Put the adapter into the wall socket.

5 Switch on the appliance.

6 Move the appliance through the hair slowly.

To clip in the most effective way, move the

appliance against the direction of hair growth.

Since all hair does not grow in the same

direction, you need to move the appliance in

different directions (upward, downward or

across) (Fig. 6).

Make sure that the at part of the comb is

always fully in contact with the scalp to obtain

an even result.

Make overlapping passes over the head to

ensure that you cut all the hair that needs to

be cut.

To achieve a good result with curly, sparse or

long hair, use a hand comb to guide the hair

towards the appliance.

7 Regularly remove cut hair from the comb.

If a lot of hair has accumulated in the comb,

remove the comb from the appliance and blow

and/or shake the hair out of it.

Contouring without comb

You can use the appliance without comb to clip

hair very close to the skin (0.6mm) or to contour

the neckline and the area around the ears.

Be careful when you clip without comb because

the cutting element removes every hair it

touches.

1 Pull the comb off the appliance (Fig. 7).

2 Before you start to contour the hairline

around the ears, comb the hair ends over the

ears.

3 Tilt the appliance in such a way that only one

edge of the cutting element touches the hair

ends when you shape the contours around

the ears (Fig. 8).

Only cut the hair ends. The hairline should be close

to the ear.

4 To contour the neckline and sideburns,

turn the appliance and make downward

strokes (Fig. 9).

Move the appliance slowly and smoothly. Follow

the natural hairline.

Cleaning

Never use compressed air, scouring pads, abrasive

cleaning agents or aggressive liquids such as

petrol or acetone or ethereal oils to clean the

appliance.

Note: The appliance does not need any lubrication.

Clean the appliance every time you have used it.

1 Make sure the appliance is switched off and

disconnected from the mains.

2 Remove the comb from the appliance.

3 To remove the clipping attachment, turn

it anticlockwise until the open dot on the

handle is aligned with the arrow on the

attachment (1). Then lift the attachment off

the handle (2) (Fig. 10).

4 Push the centre top end of the cutting

element upwards with your thumb

until it opens and then pull it off the

appliance (Fig. 11).

Be careful that the cutting element does not fall on

the oor.

5 Clean the cutting element with warm water

(max. 40°C).

6 Clean the clipping attachment under warm

running water to ush out the cut hair that

has accumulated in the attachment (Fig. 12).

7 After cleaning, place the lug of the cutting

element in the slot of the clipping attachment

and push the cutting element back onto the

clipping attachment (Fig. 13).

8 Clean the handle and the adapter with the

cleaning brush supplied or a dry cloth.

Note: The handle and the adapter are not water-

proof.

9 Let the cutting element and the clipping

attachment dry completely before you

reassemble the appliance.

4222.002.8011.1

2/9

Philips qc 5045 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info