Bedienungsanleitung Philips-Saeco HD8836 Syntia (Seite 26 von 28) (Englisch)

489712

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

• 26 •

Machine Actions Causes Solutions

The machine does not turn on. The machine is not connected to the power

source.

Connect the machine to the power source.

The co ee is not hot enough. The cups are cold. Warm the cups with hot water.

No hot water or steam is dispensed. The hole of the steam wand is clogged. Clean the hole of the steam wand using a pin.

Make sure that the machine is turned off

and has cooled before performing this ope-

ration.

Pannarello is dirty (if supplied). Clean the Pannarello.

The co ee has little crema.

(see note)

The coffee blend is unsuitable, the coffee is not

freshly roasted or the grind is too coarse.

Change co ee blend or adjust the grind as explained

in the “Co ee Grinder Adjustment” section.

The machine takes a long time to warm up

or the amount of water dispensed from the

wand is too little.

The machine circuit is obstructed by limescale

build-up.

Descale the machine.

The brew group does not come out. The brew group is out of place. Turn the machine on. Close the service door. The

brew group automatically returns to the correct

position.

Co ee grounds drawer is inserted. Remove the co ee grounds drawer  rst, then the

brew group.

The machine grinds the co ee beans but no

co ee comes out.

(See note)

Water tank is empty. Fill the water tank and prime the circuit (section

“Using the machine for the first time or after a

long period of inactivity”).

Brew group is dirty. Clean the brew group (section “Brew Group”).

Circuit is not primed. Prime the circuit (section “Using the machine for

the  rst time or after a long period of inactivity”).

Rare event that occurs when the machine is auto-

matically adjusting the dose.

Brew a few co ees as described in section “Saeco

Adapting System”.

The dispensing spout is dirty. Clean the dispensing spout.

The co ee is too weak.

(see note)

Rare event that occurs when the machine is auto-

matically adjusting the dose.

Brew a few co ees as described in section “Saeco

Adapting System”.

Co ee is brewed slowly.

(see note)

The co ee grind is too  ne. Change coffee blend or adjust the grind as ex-

plained in the “Coffee Grinder Adjustment” sec-

tion.

The circuit is not primed. Prime the circuit (section “Using the machine for

the  rst time or after a long period of inactivity”).

The brew group is dirty. Clean the brew group (section “Brew Group”).

Co ee leaks out of the dispensing spout. The dispensing spout is clogged. Clean the dispensing spout and its holes.

Note: These problems can be considered normal if the co ee blend has been changed or if the machine has just been installed.

In this case wait until the machine performs a self-adjusting operation as described in section “Saeco Adapting System”.

Please contact Saeco Customer Service or an authorized service center for any problems not covered in the above table or

when the suggested solutions do not solve the problem.

TROUBLESHOOTING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips-Saeco HD8836 Syntia Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips-Saeco HD8836 Syntia

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info