Bedienungsanleitung Philips-Saeco HD8838 Syntia (Seite 34 von 36) (Englisch)

459480

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

• 31 •

TROUBLESHOOTING

Machine Actions Causes Solutions

The machine does not turn on. The machine is not connected to the electric net-

work.

Connect the machine to the electric network.

The co ee is not hot enough The cups are cold. Preheat the cups with hot water.

No hot water or cappuccino comes out. The milk group is clogged. Clean the milk group.

Make sure that the machine is turned o and has

cooled before performing this operation.

The co ee has not enough crema.

(See note)

The coffee blend is unsuitable, the coffee is not

freshly roasted or the grind is too coarse.

Change co ee blend or adjust the grind as explained in

section "Co ee Grinder Adjustment".

The machine takes a long time to warm up

or the amount of water dispensed from the

wand is too little.

The machine circuit is clogged by limescale. Descale the machine.

The brew group cannot be removed. The brew group is out of place. Turn on the machine. Close the service door. The brew

group automatically returns to the correct position.

The co ee grounds drawer is inserted. Remove the coffee grounds drawer before removing

the brew group.

The machine grinds the co ee beans but

no co ee comes out.

(See note)

There is no water. Fill the water tank and prime the circuit (section "Using

the Machine for the First Time").

The brew group is dirty. Clean the brew group (section "Brew Group").

The circuit is not primed. Prime the circuit (section "Using the Machine for the

First Time").

Rare event that occurs when the machine is auto-

matically adjusting the dose.

Brew a few coffees as described in section “Saeco

Adapting System”.

The dispensing spout is dirty. Clean the dispensing spout.

The co ee is too weak.

(See note)

Rare event that occurs when the machine is auto-

matically adjusting the dose.

Brew a few coffees as described in section “Saeco

Adapting System”.

Co ee is brewed slowly.

(See note)

The co ee grind is too  ne. Change co ee blend or adjust the grind as explained in

section "Co ee Grinder Adjustment".

The circuit is not primed. Prime the circuit (section "Using the Machine for the

First Time").

The brew group is dirty. Clean the brew group ("Brew Group" section).

Co ee leaks out of the dispensing spout. The dispensing spout is clogged. Clean the dispensing spout and its holes.

Note: These problems can be considered normal if the co ee blend has been changed or the machine is being installed for

the  rst time. In this case wait until the machine performs a self-adjusting operation as described in section "Saeco Adapt-

ing System".

Please contact customer service for any problems not covered in the above table or when the suggested solutions do not

solve the problem.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips-Saeco HD8838 Syntia Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips-Saeco HD8838 Syntia

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info