Bedienungsanleitung Philips-Saeco SM7684 Xelsis (Seite 9 von 128) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

711393

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

AquaClean filters as indicated by the machine and in this user manual, you don't have to descale your

machine for up to 5000 cups. With each filter you can enjoy up to 625 cups, depending on the

selected coffee varieties and the rinsing and cleaning frequencies.

Preparing the AquaClean filter for activation

Before you place the AquaClean filter in the water tank, you need to prepare it for use:

1 Shake the filter for about 5 seconds (Fig. 1).

2 Fully immerse the filter upside down in a jug with cold water for at least 30 seconds. Wait until no

more air bubbles come out (Fig. 2).

3 Push the filter onto the filter connection to the lowest possible point. (Fig. 3)

Activating the AquaClean filter

You need to activate every new AquaClean filter that you use. By activating the AquaClean filter, the

machine monitors the capacity of the AquaClean filter and the number of filters used. There are 3

ways to activate the AquaClean filter.

1. Activating the AquaClean filter during first installation

After switching on for the first time, the machine guides you through the first installation steps such as

filling the water tank, filling the water circuit and activating the AquaClean filter. Simply follow the

instructions on the screen.

2. Activating the AquaClean filter when prompted

Replace the AquaClean filter when the screen shows the message 'Replace AquaClean filter?'. Then

follow the instructions on the screen to activate the filter properly.

Replace the AquaClean filter at least every 3 months, even if the machine has not yet indicated that

replacement is required.

3. Activating the AquaClean filter at any other time

You can start using the AquaClean filter at any time by following the instructions below.

1 Tap the Settings

icon and then select 'AquaClean' (Fig. 4).

2 Select 'new' and when the activation screen appears, press the start/stop button.

3 Follow the instructions on the screen.

Note: In some situations the machine will tell you that you need to descale the machine before you

can install and activate a new AquaClean filter. This is because your machine has to be completely

limescale-free before you start to use the AquaClean filter. Follow the instructions on the screen.

Measuring water hardness

During first installation, you have to set the water hardness. Follow the steps on the screen and use

the water hardness test strip supplied. To set the water hardness later, tap the Settings icon and

select 'water hardness'.

1 Immerse the water hardness test strip in tap water for 1 second. Then wait for 1 minute.

2 Check how many squares have turned red.

3 Select the appropriate water hardness setting and tap the OK icon to confirm.

Number of red squares:

Value to be set 1 2 3 4

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips-Saeco SM7684 Xelsis Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info