Bedienungsanleitung Philips SBCSC365 (Seite 4 von 75) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

36844

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

IMPORTANT!

This Baby Monitor is intended as an aid. It is not a substitute for responsible and proper adult

supervision and should not be used as such.

Make sure the Baby unit and adapter cable are always out of reach of the baby, at least 1 metre away.

Never place the Baby unit inside the baby’s bed or playpen!

The antennas on the Parent and Baby units are fixed; do not try to extend them.

Never cover the Baby unit (with a towel, blanket, etc.)

CONGRATULATIONS

You have just purchased a high-performance, cordless Baby Monitor that lets you listen to your child

from wherever you are in and around the house. Please read this guide carefully before using the

monitor, and keep it for future reference.

GETTING THE UNITS READY FOR USE

Baby unit

Connect the AC power adapter (A-9) to an AC mains socket, and then connect the cord to the DC

power supply socket (A-6) of the Baby unit.

If you want to use batteries, remove the battery compartment cover (A-8) using a screwdriver. Insert

four 1.5V, AA batteries (not included; we recommend non-chargeable Philips Alkaline batteries), noting

the + and - configuration inside the battery compartment. Put the cover back in place and tighten screw.

The Baby unit operates cordlessly for up to 30 hours on fresh batteries. The red POWER light (A-2)

flashes when battery power is low. If this happens install new batteries.

Note: To switch off the Baby unit completely push the POWER button (A-4) .

Parent unit

The Parent unit uses rechargeable batteries. These are already installed, but first they must be charged

for at least 14 hours as follows before using the unit outside the charging base:

• Connect the AC power adapter (B-11) to an AC mains socket, and then connect the cord to the DC

power supply socket (B-10) of the charging base (B-6).

• Place the Parent unit inside the charging base. The red charging light (B-13) lights.

The Parent unit can be operated now but you should leave it in the charging base until the batteries are

fully charged (at least 14 hours). When the batteries are fully charged, take the Parent unit out of the

charging base and use cordlessly for up to 12 hours.

When the red POWER light (B-1) on the Parent unit flashes, the battery power is low. Place the Parent

unit inside the charging base to recharge the batteries.

If the rechargeable batteries begin to lose their effectiveness, replace them with four new batteries

(1.2V, AA NiMH) as follows: remove the battery compartment cover (B-7) using a screwdriver and insert

the batteries noting the + and - configuration inside the battery compartment. Put the cover back in

place and tighten screw. Only use 1.2V, AA NiMH rechargeable batteries!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips SBCSC365 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info