Bedienungsanleitung Philips SC2008 (Seite 28 von 86) (Englisch, Holländisch, Französisch)

537195

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

Problem Possible cause Solution

The adapter is not

inserted properly

into the wall socket

and/or the small

plug is not inserted

properly into the

appliance socket.

Make sure the adapter is inserted properly into the

wall socket and/or the small plug is inserted properly

into the appliance socket.

The appliance is

defective.

Contact the Consumer Care Centre in your country,

your Philips dealer or a Philips service centre.

I have switched on the

appliance but I cannot

increase or decrease the

light intensity.

The appliance has

to be reset.

To reset the appliance, switch off the appliance and

then switch it on again. If you still cannot adjust the light

intensity, contact the Consumer Care Centre in your

country, your Philips dealer or a Philips service centre.

The ‘ready to ash’ light

does not go on when I

place the appliance on

the skin.

You have not put

the attachment

with safety ring

properly on the

skin.

Place the appliance at a 90° angle onto the skin in such

a way that all contact switches touch the skin. Then

check if the ‘ready to ash’ light is on and press the

ash button.

If this does not work, place the appliance on a part

of your body where it is easy to establish full skin

contact, for example on your lower arm.Then check

if the ‘ready to ash’ light works. If the ‘ready to ash’

light still does not go on when you place the appliance

on the skin, contact the Consumer Care Centre in your

country, your Philips dealer or a Philips service centre.

The safety ring is

dirty.

Clean the safety ring carefully. If you are unable to clean

the safety ring properly, contact the Consumer Care

Centre in your country, your Philips dealer or a Philips

service centre to replace the attachment.

The ‘ready to ash’ light

does not go on when I

place an attachment on

my skin, but the cooling

fan works.

The overheat

protection has

been activated.

When the overheat protection has been activated, the

fan still works. Do not switch off the appliance and let it

cool down for approx. 15 minutes before you continue

to use it. If the ‘ready to ash’ light still does not go on

when you place the appliance on the skin, contact the

Consumer Care Centre in your country, your Philips

dealer or a Philips service centre.

The ‘ready to ash’ light is

green but the appliance

does not produce a ash

when I press the ash

button.

The appliance

needs to be reset.

To reset the appliance, switch off the appliance and switch

it on again. If the ‘ready to ash’ light is green but the

appliance still does not produce a ash when you press

the ash button, contact the Consumer Care Centre in

your country, your Philips dealer or a Philips service centre.

The appliance becomes

warm during use.

This is normal. No action required.

The appliance does not

show light intensity 1

when I switch it on.

The appliance

needs to be reset.

To reset the appliance, switch it off and on again. If the

appliance still does not show light intensity 1, contact

your Customer Care Centre, your Philips dealer or a

Philips Service Centre.

ENGLISH28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips SC2008 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips SC2008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info