Bedienungsanleitung Philips scd469 (Seite 12 von 188) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

368271

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

Nightlight

1 Press the nightlight button Q to switch the nightlight on or off. (Fig. 26)

When you run the baby unit on batteries, switch off the nightlight to save power.

Dial-up mode

In this mode, the baby unit calls a preprogrammed phone number if a sound is detected. You can

also phone the phone number to which the baby unit is connected to check on your baby.

Setting the baby monitor up for dial-up mode

1 Switch on the baby unit and the parent unit.

2 Make sure that:

the telephone cable supplied is connected to the phoneline-in socket of the baby unit.

at least one telephone number is stored in the memory of the baby unit.

3 Press the MODE button on the baby unit to set the unit to dial-up mode. (Fig. 15)

Note:If

Ç lights up on the display, there is no connection to the telephone network. Follow the steps in

‘Preparing the baby monitor for dial-up mode’ to establish a connection with the telephone network.

4 Press the M (memory) button to select the telephone number. (Fig. 12)

If you have used Quick Install to enter a telephone number in the memory, press M1.

If you have programmed the baby unit with the PRG button, choose one of the telephone

numbers stored in the memory (M1-M5).

5 Push the SENSITIVITY slide to the desired microphone sensitivity level. (Fig. 21)

See ‘Microphone sensitivity’ for instructions on how to set the microphone sensitivity of the

baby unit.

Tip:We advise you to test the dial-up function before you leave by making a sound close to the baby unit.

Of course, this is easiest when you have programmed your mobile phone number.

Answering a call of the baby monitor

When the baby unit picks up a sound, it calls the preprogrammed telephone number after the

preset sensitivity time. If the call is not answered, the baby unit calls again after 1 minute.

1 Answer the phone to listen to your baby.

2 Press the # button on the telephone to talk to your baby.

After 3 minutes, the baby unit disconnects.

3 Press the * button on the telephone or hang up to disconnect.

If the baby unit detects a sound again, it calls the preprogrammed telephone number again.

Calling the baby monitor to check on your baby

Note:To call the baby unit, use a tone-dial telephone with a keypad. This function does not work on pulse-

dial telephones and on telephones with a dial.

1 Dial the number of the telephone line the baby unit is connected to.

After 3 rings, the baby unit is activated and asks you to enter your PIN code.

2 Enter your PIN code with the numeric keys on the telephone.

You can now hear your baby.

Note:If you enter the wrong PIN code three times, the baby unit disconnects.

3 Press the # button on the telephone to talk to your baby.

After 3 minutes, the baby unit disconnects.

4 Press the * button on the telephone or hang up to disconnect.

ENGLISH12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips scd469 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info