Bedienungsanleitung Philips scd520 00 dect babyfoon (Seite 9 von 196) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

368382

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

, When the batteries are fully charged, the display of the parent unit shows a full battery

symbol T.

- When you charge the parent unit for the rst time or after a long period of disuse, switch it

off and let it charge continuously for at least 10 hours.

- Charging normally takes 8 hours, but it takes longer when the parent unit is switched on while

charging. To keep the charging time as short as possible, switch off the parent unit during

charging.

- When the batteries are fully charged, the parent unit can be used cordlessly for at least 24

hours.

Note: When the parent unit is charged for the rst time, the operating time is less than 24 hours. The

batteries only reach their full capacity after you have charged and discharged them four times.

Note: When the parent unit is not in the charger, the batteries gradually discharge, even when the parent

unit is switched off.

Using the appliance

1 Place the parent unit and the baby unit in the same room to test the connection (Fig. 10).

Make sure the baby unit is at least 1 metre/3 feet away from the parent unit.

2 Press and hold the on/off button 3 on the baby unit until the green power-on light goes

on. (Fig. 11)

Note: The power-on light always lights up green, even when there is no connection with the parent unit.

, The nightlight lights up briey and then goes out again.

, The battery light T lights up briey and then goes out again. (Fig. 12)

3 Press and hold the on/off button 3 on the parent unit until the sound level lights light up

briey. (Fig. 13)

, The display goes on and the battery symbol appears on the display (Fig. 14).

, The LINK light ashes red and the message ‘Searching’ appears on the display. (Fig. 15)

, The LINK light on the parent unit turns green and lights up continuously when a connection

has been established between the baby unit and parent unit. The message ‘Linked’ appears on

the display. (Fig. 16)

, After 2 seconds the message ‘Linked’ disappears and the temperature value is shown on the

display. (Fig. 17)

, If no connection is established, the LINK light on the parent unit stops ashing and lights up

red. The parent unit beeps from time to time and the message ‘Not Linked’ appears on the

display. (Fig. 18)

Positioning the baby monitor

1 Place the baby unit at least 1 metre/3 feet away from your baby (Fig. 19).

2 Place the parent unit within the operating range of the baby unit. Make sure it is at least 1

metre/3 feet away from the baby unit to avoid acoustic feedback (Fig. 20).

For more information on the operating range, see section ‘Operating range’ below.

Operating range

The operating range of the baby monitor is 330 metres/1000 feet in open air. Depending on the

surroundings and other disturbing factors, this range may be smaller. Indoors the operating range is

up to 50 metres/150 feet.

Dry materials Material thickness Loss of range

Wood, plaster, cardboard, glass

(without metal, wires or lead)

< 30cm/12in 0-10%

ENGLISH 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips scd520 00 dect babyfoon Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info