811249
12
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
12 Philips · Screeneo U4
Bluetooth connection
The projector is equipped with Dual Bluetooth
5.0 technology, allowing you to connect to
up to 2 speakers or sets of headphones. You
can independently control the volume of each
connected device.
Before you can use the projector with Bluetooth
speakers or headphones for the first time, you
must pair the projector with them. The projector
will automatically connect to a device as soon
as they are paired.
Notice
Be sure that the Bluetooth device is
no farther than 10 m (33 ft) from the
projector when connecting the two.
Even when connecting within the
specified communication distance,
connections can be lost due to the signal
status.
Pairing
Speaker/Headphones 1 Speaker/Headphones 2
ON
13
2
4
1 Make sure the projector is on.
2 Turn on your Bluetooth speaker or
headphones and make sure it is in pairing
mode. Press the pairing button on the
device, if needed. See the documentation
supplied with the device for more
information.
3 Press either of the buttons on the
projector to pair the projector with the
device.
Once you press this button, the
projector enters pairing mode and
displays "Searching" on the screen.
Also, its power LED blinks in light blue.
When the pairing is complete, the
projector briefly displays "Paired
successfully" on the screen, as well as
the name of the paired device. Also, its
power LED turns solid light blue.
If no pairing is created, the projector will
automatically exit pairing mode in 10
seconds.
4 To pair a second Bluetooth speaker or set
of headphones, repeat steps 2 and 3 above
but press the other button in step 3.
Tips:
The projector will automatically switch its
audio output to Bluetooth output after
connecting to a Bluetooth device.
After connecting a Bluetooth device,
press / on the remote control to
adjust the volume to the desired level. To
independently control the volume of each
connected device, use the volume control
of that device.
Disconnect a Bluetooth device
Use one of the following methods to disconnect
a Bluetooth device from the projector but leave
it paired.
The projector automatically switches its audio
output to internal speaker when no Bluetooth
device is connected.
Terminate the Bluetooth connection
from the Bluetooth device, or turn off the
Bluetooth device. The projector will briefly
display "Disconnected" on the screen.
Turn off the projector.
Reconnect a Bluetooth device
Once you pair and connect a Bluetooth
device to the projector using the steps above,
the projector will automatically reconnect
unless the Bluetooth device gets unpaired
or turned off. The projector briefly displays
"Paired successfully" on the screen after a
reconnection.
Unpair a Bluetooth device
This will remove the Bluetooth device from the
projector's memory. You'll need to pair and
connect this device to use it again.
To unpair a Bluetooth device, press and hold
the corresponding button on the projector for
3 seconds while the device is connected. The
projector briefly displays "Disconnected" on the
screen after the unpairing.
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Philips SCN350 Screeneo U4 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Philips SCN350 Screeneo U4

Philips SCN350 Screeneo U4 Bedienungsanleitung - Deutsch - 28 seiten

Philips SCN350 Screeneo U4 Bedienungsanleitung - Holländisch - 25 seiten

Philips SCN350 Screeneo U4 Bedienungsanleitung - Französisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info