Bedienungsanleitung Philips SRU 3005 (Seite 9 von 29) (Englisch, Französisch, Spanisch)

105793

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

1716

The learning feature allows you to “learn” functions

from your original remote control. For example - you may

want to use your remote to operate the RANDOM PLAY

feature from your original CD remote control. This

remote is equipped with an “easy learning” feature that

allows you to “learn” features (such as RANDOM PLAY

from your original CD remote) by following the steps

below, and on the next page:

1. Press and hold the SETUP button until the red

indicator turns on, then release the button.

2. Press and release the desired mode button (TV,

VCR, etc.), the red indicator blinks then stays on.

3. Press and release the LEARN button, the red

indicator blinks then stays on.

4. Press and release the Learning Remote button that

you want to teach (e.g. POWER).

5. Point both remotes facing each other by approxi-

mately 1 inch apart (see tips on page 14).

6. Press and hold the Original Remote button (e.g.

Power) until the red indicator blinks once and stays

on. If there is a learning problem, the indicator blinks

for three seconds and stays on. If this happens,

repeat Steps 4 to 6.

7. Repeat Steps 4-6 for other buttons you want to

learn.

8. Press and release the SETUP button when all desired

remote commands are learned. Code Learning is now

complete.

Learning Commands

Line up your remotes (that you’re learning from) in front of

the Learning remote, on a hard surface approx. 1 inch apart.

This feature assists you in identifying where your

original remotes IR transmitter is located and is

particularly useful if your original remote’s IR

transmitter is hidden behind a lens.

1. Point both remotes facing each other by

approximately 1 inch apart (see Tips on Learning on

previous pages)

2. Press and hold the SETUP button until the red

indicator turns on, then release the button.

3. Press and release the desired Mode button (TV,

VCR, etc.), the red indicator blinks then stays on.

4. Press and release the LEARN button, the red

indicator blinks then stays on.

5. Press and hold any Original Remote button and

move the Original Remote to the left and right, and/

or, up and down in front of the Learning remote IR

transmitter. The red indicator will remain on if no IR

from the Original remote is found and the red

indicator will blink on and off more rapidly when the

IR transmitters are lining up. The point where the

red indicator blinks most rapidly is where the two IR

transmitters are aligned. Note some original remotes

will only transmit IR on the initial button press then

stop. In these cases, quickly press and release the

original remote button repeatedly during this

procedure.

6. You can now learn a button from your original

remote by continuing from “Step 4” in the

“Learning Commands” section on the next page, or,

to exit at this point, press and release the SETUP

button

IR Transmitter Finder Feature

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips SRU 3005 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips SRU 3005

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info