Bedienungsanleitung Philips VR1100 (Seite 11 von 39) (Englisch)

462271

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

— 12 —

Do NOT press any button on the front panel or remote control until the display window shows either the display as

illustrated in step 2 or “– –:––”.

As AUTO CH. SET

progresses, the “7” mark

moves from left to right.

1¶ If you are referring to the display window, press

5/∞ to select “Auto” and press OK/STATUS.

ETTING

(CONTINUED)

Auto Set Up

¶ If you are referring to the on-screen display, press 5/∞ to

select “AUTO CH. SET” and press OK/STATUS.

AUTO CH. SET

PLEASE WAIT

END : MENU

+++

Beginning

End

\ AUTO CH. SET

FOLLOW TV

SELECT:

∞

CONFIRM: OK

END : MENU

2¶ If you have connected the VCR to TV via an RF

cable only (RF connection), the channel that is

shown on the display window is your Video Channel.

If you have selected MAGYARORSZAG (36),

CESKA REPUBLIKA (42), POLSKA (48) or

OTHER EASTERN EUROPE (EE) in Preparation

section, “2OUT” appears instead of “1OUT”.

To view picture signals from the VCR, set TV to the

Video Channel. Refer to the instructions supplied

with TV set for how to do this.

¶ If you have connected the VCR to TV via both an RF

cable and a SCART cable or an S-Video cable (SCART

connection or S-Video connection), you do not need the

video channel so you have to set the video channel to

off.

Press ∞ until the video channel changes to “– –” (off).

To view picture signals from the VCR, set the TV to its

AV mode. Refer to the instructions supplied with the

TV set for how to do this.

¶ If “– –:––” appears, both Auto Channel Set and Auto Clock Set have failed.

Make sure the TV antenna cable is connected correctly and press OK/STATUS to re-perform the Auto Set Up.

3Press OK/STATUS.

If the correct current time is displayed on the display window, the Auto Channel Set and Clock Set

have been completed successfully. Go to step 4.

If “1” (channel position) is displayed on the display window, the Auto Clock Set has not completed

(only the Auto Channel Set has). Go to step 4 and then perform “Clock Set” manually. (✈P.20)

¶ You can check if the Guide Channel numbers have been set correctly when you perform S

HOWVIEW Timer

Recording (✈P.29); if the correct channel position number is displayed on S

HOWVIEW Programme screen, this

confirms that the Guide Channel number for the SHOWVIEW number you enter has been set correctly.

4Press PROGRAMME

5/∞

on the front panel (or CH

5/∞

on the remote control) to make sure that all necessary

stations have been stored in the VCR’s memory.

¶ If station names (ID ✈P.19) have also been stored in the VCR’s memory, the station name will be displayed at the

top left corner of the screen for about 5 seconds when the VCR is tuned to a different station.

¶ If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or station

names, see pages 17–18.

¶ If no station is stored in the VCR’s memory, make sure the TV antenna cable is connected correctly and turn off the

VCR power once, then turn it back on again. Re-perform from Preparation on page 10.

Untitled-2 16/08/2000, 15:3612

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips VR1100 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info