Bedienungsanleitung Philips VR1100 (Seite 30 von 39) (Englisch)

462271

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

— 31 —

Useful function for Timer

Recording: Auto Tape Speed

With this function activated, the VCR can

change the tape speed and record the

programme in LP mode if not enough

tape remains for recording in SP mode.

1 Press VCR.

2 Press MENU.

3 Press 5 or ∞ to select “VCR SET

UP”, then press OK/STATUS.

4 Press 5 or ∞ to select “AUTO SP =

LP TIMER.”

5 Press 4.

Each time you press the button, the

setting changes.

ON:

Select this to allow the VCR to

change the tape speed from SP to

LP when there is not enough tape

length remaining.

OFF:

Select this not to allow the VCR to

change the tape speed.

6 Press MENU to exit from the menu

operations.

Notes:

• The Auto SP

LP Timer feature is not

available during OTR (One Touch

Recording) and the feature will not work

properly with any tapes longer than E-

180 or with some tapes of shorter lengths.

• If you have programmed the recorder to

timer-record 2 or more programmes, the

second programme and those hereafter

may not fit on the tape if you set “AUTO

LP TIMER” to “ON”. In this case,

make sure the mode is not engaged, then

set the tape speed manually during timer

programming.

• In order to ensure that the recording fits on

the tape, this feature may leave a short non-

recorded section at the end of the tape.

• There may be some picture noise and sound

disturbance at the point on the tape where

the recorder switches from SP to LP mode.

• If you perform timer recording with both

VPS/PDC and the Auto SP

LP Timer

activated, and the programme goes

beyond its originally scheduled length,

there may be times when the programme

cannot be recorded in its entirety.

When two programme overlap

The Program

Review

screen will

appear with

a magenta

line blink-

ing on the

newly set

timer recor-

ding, while the other overlapped

programme blinking.

1 Press 5 or ∞ to move

the mage-

nta line

among the

two over-

lapping

programs.

2 Press OK/

STATUS

to view

the detail information of the

program you want

to change.

3 Go to step 4 through 9 on page 30 for

Timer Recording to modify the

selected program. To cancel any

timer recording, press CLEAR.

• If you do not modify the overlapping

programs, the VCR will record the earlier

program completely. Only the remaining

part of the later program will be recorded.

• If the START time for the two programs

are the same, the lower program number

will be recorded.

ONE TIME PROGRAM

PROGRAM 1

TV PROG +/- 12

START+/- 08:00

STOP +/- 10:00

REC SPEED SP

VPS/PDC ON

DATE +/- 21/07/00

FRIDAY

ERASE : CLEAR

CONFIRM : OK END : TIMER

PR CH START STOP DATE

1 12 08:00 10:00 21/07

2 25 11:00 13:00 10/08

3 03 09:00 11:00W14/07

4 45 03:00 03:15W15/10

SELECT : 5∞

CONFIRM : OK

Turbo Timer

This function allows you to set the

timer recording program without going

through the regular set up with the on

screen. The extent of programming is

24 hours from the current time.

1 Insert a tape into the VCR and press

the “TURBO TIMER” button on the

remote control. Current time will

appear on the display panel.

2 To change the START time, press the

5 or ∞ ( if you press and hold the

button, the time changes in

30-minute increments) then press

OK/STATUS.

3 To change the STOP time, press the

5 or ∞ ( if you press and hold a

button, the time changes in

30-minute increments) then press

OK/STATUS.

4 To change the CHANNEL position,

press the 5 or ∞, then press

OK/STATUS.

5 The data input will be memorized

and the Turbo Timer mode will be

finished so that normal display

appears.

6 Turn off the VCR.

Notes:

• To exit Turbo Timer mode at any step,

press the TURBO TIMER button.

• If “Err” appears on the display panel,

all eight programs have been set and

Turbo Timer will not proceed. To

remove the error message, press the

TURBO TIMER button again.

• Settings of Turbo Timer will appear

on the display panel only and not on

the screen.

• Programs Overlap Warning does not

function with Turbo Timer.

• DAILY or WEEKLY programming

are not available on Turbo Timer.

• Tape speed can be selected anytime

during steps 2 through 4.

VCR

Untitled-2 16/08/2000, 15:3831

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips VR1100 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info