Bedienungsanleitung Phoenix UF0961 (Seite 1 von 1) (Englisch)

737014

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

Ph Sf Cpny r eac n s gurte

PLEASE READ CAREFULLY

INTRODUCTION

To ensure their high security attributes, Underoor Safes require a High

Grade Concrete Encasement containing suitable reinforcement.

OPENING THE SAFE

UF0600 Series - To open the safe insert one of the keys supplied and

turn. Lift the handle and the lid can be taken out of its housing.

UF0900 Series - To open the safe insert one of the keys supplied and

turn. Lift the handle and spin the lid until it aligns and comes out of its

housing.

LOCATION

The installation should be undertaken by a qualied installer whose survey

would determine a convenient ground oor site free from any electrical

wiring, water or gas pipes, etc., and where the use of attacking tools would

be restricted.

INSURANCE

If the safe is for insurance requirements your insurance company should

be made aware of your intention prior to installation.

WHEN THE INSTALLATION IS COMPLETE NO PORTION OF THE

NECK OR DEPOSIT TUBE MUST PROTRUDE ABOVE FLOOR LEVEL.

SAFE PREPARATION

1. Remove door from safe to a place away from site to avoid any form of

contamination.

2. To prevent dust or concrete from entering during installation ll the

inside of the safe and neck with crumpled newspaper.

3. Apply sealant around neck-to-collar joint.

Replace lid

REINFORCEMENT

Steel reinforcement can be used. A suitable type is Weldmesh Ref. No.26:

2” x 2” (50 mm x 50mm) x 6 S.W.G.

SITE PREPARATION

1. Remove any oor covering and expose concrete oor.

2. Mark an area on the oor to allow not less than 6” (150mm) of

concrete round the sides of the safe.

3. Cut through the concrete and excavate to a depth of 3” (75mm) more

than the total depth of the safe.

4. Angle the sides of the hole outwards by 2” in order that the concrete is

dovetailed into the oor.

5. For installation in a wooden oor it will be necessary to conne the

concrete to the dimensions given with the use of shuttering.

CONCRETE PREPARATION AND DAMP-PROOFING

Use only good quality sand, aggregate and cement.

Recommended Specication:

PARTS BY WEIGHT

Coarse Graded Aggregate ¾” MAX 3

Fine Graded Aggregate 3/16” MAX 1 ½

Ordinary Portland Cement 1

Water Not to exceed 24.4 litres for every

50 kgs of Cement

All materials to conform to the appropriate Bristish Standard Specication.

A suitable dry mix preparation is Marley Mix 3-1 ½ - 1 B.S 5838 Part 1

DO NOT CONCRETE UNLESS THE AMBIENT TEMPERATURE IS AT

LEAST 3ºc MIN.

Materials must be frost free and in cold conditions use water heated to

10ºC. Accelerating or other admixtures containing calcium chloride must

not be used as these are highly corrosive. The addition of a waterproof-

ing agent, however, may be necessary. Where site excavation reveals

extreme damp presence, the hole should be lined with a heavy gauge

polythene sheeting.

Thoroughly dry mix all materials and then add a minimum of water to allow

the concrete to be compacted. Do not add too much water as this will

reduce the strength of the construction. The amount of water shown in the

column above produces a 2” (50 mm) slump which should not be

exceeded.

SAFE INSTALLATION

1. Cover the base of the hole with 4” (100 mm) of the concrete mix.

2. Lift safe by top plate, place in centre of hole and work down into the

concrete bed until the lid is at the correct level with surrounding oor.

3. Use a spirit level to span the hole to check the safe is level.

4. The concrete is added in layers of 4” (100mm): each layer worked

well into the previous layer with a tamping tool. A section of timber,

or similar, about 39” (1m) long, with a ramming face approximately

1” (25mm) square is ideal for the purpose. Work methodically over

entire surface and ensure full compaction of concrete. Take care not to

disturb the safe or dislodge the neck through-out installation.

5. The steel reinforcement is introduced into the concrete at the appropri-

ate stage.

6. When the hole is lled with the concrete mix to within ½ “ (12mm) of

the surface, take the safe door from bag and after removing lid, insert

door into safe to ensure that misalignment has not occurred. ANY

NECESSARY ADJUSTMENT WOULD NEED TO BE MADE NOW

BEFORE CONCRETE IS SET.

7. Screed last ½“ (12mm) with a mixture of sand and cement to bring to

a smooth nish.

THE SAFE MUST NOT BE USED FOR 14 DAYS AFTER

INSTALLATION.

CARE AND MAINTENANCE

The subsequent application of a lino paint by the owner/user will act as a

surface stabiliser and help to control grit. Ensure that any oor washing

activity etc. does not result in water entering the safe. Keep safe door

and locating collar dry, clean and lightly oiled. Dirt and grit etc. can be

damaging to the locking mechanism. To ensure that the safe remains in

good working order always close the escutcheon and see that the lid is

replaced properly after use. The use of silica gel is recommended where

condensation is a problem or where the safe remains locked for any

extended period of time.

GUARANTEE REGISTRATION

Please submit your guarantee registration by visiting our website

www.phoenixsafe.com and clicking on guarantee registration.

For further assistance or information

please contact us on 0151 944 6444.

APEX HOUSE, 1 ORRELL MOUNT, LIVERPOOL, L20 6NS,

UNITED KINGDOM | +44 (0)151 944 6444

V1/PB/FEB 19

INSTRUCTIONS FOR INSTALLING UNDERFLOOR

SAFES IN CONCRETE AND WOODEN FLOORS

& GUARANTEE REGISTRATION

Phoenix UF0961 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info