Bedienungsanleitung Piazzetta P963 M (Seite 8 von 72) (Englisch)

643487

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

a The stove requires a UL listed pellet vent. So the venting system shall be approved for pellet stoves by a certied testing Laboratory.

a PL Vent must be used for venting all Freestanding stoves.

d Do not use to vent pellet appliance these venting materials and products:

- Dryer vent

- Gas appliance (Type B) vent

- PVC (plastic) pipe

- Single wall stove pipe.

a The pellet stove is not the same as other stoves. It has a forced draught of ue gas by a fan, which keeps the rebox in a vacuum

and the entire ueway slightly pressurised. For this reason the ue must be completely airtight and correctly installed to ensure both

trouble-free operation and user safety.

• The ueway must be made by specialised personnel or rms, as outlined below.

• The ue must be installed in such a way as to guarantee that periodic cleaning can be carried out without dismantling any parts whatsoever.

• Pipes should always be sealed with silicone (not cement-based sealants) or specially adapted gaskets/seals, which retain their strength and

elasticity at high temperatures (>450°F / 230°C), and should be xed with at least three sheet metal screws.

a Using the relative pipe clips, x the ue to the wall so that it does not weigh on the smoke fan.

d DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.

d DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

d Do not connect to a ueway into which extractor hoods discharge vapours.

a The very hot exhaust gases may cause skin burns: keep a considerable distance away from the appliance.

a The exhaust gases from the combustion of pellets fuel may dirty the outside of the walls. To avoid such possibility terminate the vent

above the roof line.

Pipes and maximum usable lenghts

The exhaust pipe on all stoves is 2.95” O.D. so the stove was designed to accommodate a 3” stove pipe adaptor but the diameters of the pipes

depends on the type of installation. Your installation may require the use of 4” vent as shown in Table 1.

TABLE 1: CONNECTION TO FLUE PIPE - PIPE LENGTH

TYPE OF INSTALLATION WITH 3” DIAMETER PIPE

WITH DOUBLE-WALLED 4”

DIAMETER PIPE

Maximum length (with three 90° elbows) 25’ 35’

For installations more than 4000’ (1200 m) above sea level - Required

Maximum number of elbows 3 4

Length of horizontal sections with minimum 3% gradient 10’ 10’

a Losses in pressure associated with a 90° elbow can be compared to those incurred by three feet of pipe. An inspectable union-tee

can be considered equivalent to a 90° bend.

EXAMPLE: if installing a section greater than 20’ in length with 3” diameter pipe, calculate the maximum usable length in the following ways:

• If a maximum of three 90° elbows are used, the maximum length of the section will be 25’.

• If a maximum of two 90° elbows are used and bearing in mind that a 90° bend can be replaced by 3’ of pipe, the maximum length of the section

will be 25’+3’ = 28’.

• If a maximum of one 90° elbows is used and bearing in mind that a 90° bend can be replaced by one metre of pipe, the maximum length of the

section will be 25’+3’+3’ = 31’.

DT2010229-05

1.7 FLUEWAY

H07032120 / DT2002308 – 00

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Piazzetta P963 M Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info