Bedienungsanleitung Pinell Supersound 101 (Seite 8 von 11) (Englisch)

748304

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

15 16

5.4 Settings

Dynamic range compression

Some DAB broadcasts offer dynamic range compression (DRC). This feature

allows radios to compress the dynamic range of the output audio stream,

so that the volume of quiet sounds is increased, and the volume of loud

sounds is reduced. This can be useful if you are listening to music with a

high dynamic range in a noisy environment

(for example, classical music while cooking).

To change the DRC of the IR1, select Menu > DRC, and then DRC high,

DRC low or DRC off.

Note: The IR1’s DRC setting does have any effect if DRC data is not

included in the broadcast.

Station order

You can choose the order of the DAB station list to be either

Alphanumeric, Ensemble or Valid. Ensemble lists groups of stations that

are broadcast together on the same ensemble, for example BBC or South

Wales local. Valid lists valid stations first, alphanumerically, then off-air stations.

To change station order, select Menu > Station order > then

Alphanumeric or Ensemble.

6. FM radio mode

FM radio mode receives analogue radio from the FM band and displays RDS

(Radio Data System) information about the station and show (where broadcast).

To enter FM mode, either press Mode to choose FM Radio.

6.1 Selecting stations

To find a station, press and hold Select knob. The frequency display

starts to run up as IR1 scans the FM band.

resets to store an FM preset, press and hold button 1-3+ Preset until the

display shows the Save preset screen. Select one of the 20 presets to

save the currently playing station.

To select a preset, press Preset 1-3+ briefly, then select one of the listed

Preset stations. When a preset station is playing, it shows ☆1,2,3 etc in

the middle of the screen.

6.2 Now playing information

While an FM station is playing, the screen shows one of the two

following sets data:

If RDS information is available, by default the service name

(i.e. station name) is displayed.

You can cycle through further RDS information by pressing Info .Each

time you press Info, another set of information is displayed, cycling

through RDS radio text, RDS programme type, frequency and today’s date.

If no RDS information is available, the currently tuned frequency is shown.

6.3 Settings

Scan settings

By default, FM scans stop at any available station. This may result in a

poor signal-to-noise ratio (hiss) from weak stations. To change the scan

settings to stop only at stations with good signal strength, select

Menu > Scan setting > Strong stations only? > Yes.

Audio settings

By default, all stereo stations are reproduced in stereo. For weak stations,

this may result in a poor signal-to-noise ratio (hiss). To play weak stations

in mono, select Menu >Audio setting > FM weak reception: Listen in

mono only > Yes.

7. Bluetooth mode

Prior to pairing, verify your device supports Bluetooth 4.2+EDR A2DP and

your device is not connected to any other Bluetooth product. Devices

may pair differently. Below is a general guide.

the different display options (thumbnail, slide with DLS text and full screen slide)

press and hold the info button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pinell Supersound 101 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pinell Supersound 101

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info