Bedienungsanleitung Pioneer A-70DA (Seite 6 von 116) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

651674

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

02 Connecting up

• When using speakers with removable network

circuits, note that if the network is removed, no

effect will be produced and damage may be caused

to the speaker.

• Another method of connection is to connect the

SPEAKERS A terminals to HIGH and the SPEAKERS

B terminals to LOW (reverse that shown in the

illustration).

Connecting speaker cables

1 Twist the cable cores.

2 Loosen the nut on the

SPEAKERS

terminal, and insert the speaker cable into

the exposed hole in the terminal shaft.

3 Retighten the terminal nut.

Caution

• When using only one set of speaker terminals

(SPEAKERS A or SPEAKERS B), or when utilizing

bi-wiring connections, the speaker used should

have a nominal impedance between 4  and

16 . When using both sets of terminals, the

connected speakers should have nominal

impedance between 8  and 32 . Consult the

instructions accompanying your speakers for

details regarding the impedance value.

• Make sure the positive and negative (+/–) terminals

on the amplifier match those on the speakers.

• These speaker terminals carry HAZARDOUS live

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Make sure that all the bare speaker wire is twisted

together and inserted fully into the speaker

terminal. If any of the bare speaker wire touches the

back panel it may cause the power to cut off as a

safety measure.

Connecting audio cables

Connect the white plug to the left (L) jack, and the red

plug to the right (R) jack. Be sure to insert the plugs fully

into the jacks.

123

10 mm

Left (white)

Right (red)Right (red)

Connecting to the balanced input

terminals (A-70DA only)

Connect the BALANCED IN terminals of the unit to a

SACD player, USB DAC, network player, or other device

with balanced output terminals.

Caution

•The BASS, TREBLE, BALANCE, and LOUDNESS

functions do not work for a device connected to the

BALANCED IN terminals.

The phase may differ depending on the device to be

connected. Use the phase selector switch on the rear

panel of the unit to match the phase.

• Initial setting (No. 2 HOT)

• Settings when polarity changed

(No. 3 HOT)

Note

• For details on the phase of the balanced output

terminals of the device to be connected, refer to the

instruction manual of the device.

• When connecting the unit to a Pioneer player,

match the phase to the initial setting (No. 2 HOT).

LINE2

LINE1

USB

COAXIAL

PHONO

(MM/MC)

SIGNAL

GND

NETWORK

SACD/CD

DIGITAL IN

ANALOG IN

OPTICAL

LINE2

OUT

AMP

DIRECT

BALANCED IN

NORMAL

INVERSION

PHASE

Audio device with

balanced output terminals

Balanced cable

(sold separately)

Balanced cable

(sold separately)

A-70DA’s rear panel

NORMALNORMAL

INVERSIONINVERSION

PHASEPHASE

1 Ground

3 COLD (-)

2 HOT (+)

NORMAL

INVERSION

PHASE

1 Ground

3 HOT (+)

2 COLD (-)

A70_SYXE8_0728.book 6 ページ２０１５年７月２８日　火曜日　午後３時５４分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer A-70DA Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info