Bedienungsanleitung Pioneer anh-p10mp (Seite 94 von 109) (Englisch)

162112

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

Initial Settings

Section

Switching the guidance

display for intersection

The display can be magnified around an inter-

section to facilitate navigation (only when the

source is turned off).

1 With the source turned off, press and

hold 1.

2Press NEXT and then press N.INT to se-

lect the intersection display mode.

3Press N.INT to turn the enlarged dis-

play off.

“OFF” appears on the display.



Press N.INT again to turn the enlarged dis-

play on.

Setting the rear output

and subwoofer controller

This product’s rear output (rear speaker leads

output and RCA rear output) can be used for

full-range speaker (FULL Preout :FULL) or

subwoofer (SUB.W) connection. If you switch

the rear output setting to “SUB.W”, you can

connect a rear speaker lead directly to a sub-

woofer without using an auxiliary amp.

Initially, the unit is set for rear full-range

speaker connection (FULL Preout :FULL).

When rear output is connected to full range

speakers (when “FULL Preout :FULL” is se-

lected), you can connect the RCA subwoofer

output to a subwoofer. In this case, you can

select whether to use the subwoofer control-

ler’s (low pass filter, phase) built-in FULL Pre-

out :SUB.W or the auxiliary FULL Preout

:FULL.

1 With the source turned off, press and

hold 1.

2Press NEXT and then press REAR to se-

lect the rear output setting mode.

3Press SW or FULL to select the desired

output setting.

Pressing SW or FULL will switch between

“FULL” (full-range speaker) and “SUB.W”

(subwoofer), and that status will be displayed.



When no subwoofer is connected to the rear

speaker lead output, select “FULL Preout :FULL”.



When a subwoofer is connected to the rear

speaker lead output, select “SUB.W”.



When the rear output setting is “SUB.W”, you

cannot change the subwoofer controller (Step 4).

4Press 



or 



to switch the subwoofer

output or nonfading output (full-range

RCA output).

Pressing 



or 



will switch between

“FULL Preout :SUB.W” and “FULL Preout

:FULL” and that status will be displayed.



When adjusting the subwoofer sound by us-

ing an external amplifier, set to “FULL Preout

:FULL”.



When adjusting the subwoofer sound by us-

ing this product, set to “FULL Preout :SUB.W”.

Notes

• Even if you change this setting, there is no

output unless you turn the nonfading output

(refer to Using nonfading output on page 88)

or subwoofer output (refer to Using subwoofer

output on page 88) in the audio menu on.

• If you change the subwoofer controller, sub-

woofer output and nonfading output in the

audio menu return to the factory settings.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer anh-p10mp Seite 94

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer anh-p10mp

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info