Bedienungsanleitung Pioneer AVH-280BT (Seite 32 von 45) (Englisch)

649351

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

Power cord

1 To power supply

2 Power cord

3 Yellow

To terminal supplied with power regardless of ignition switch

position.

Red

To electric terminal controlled by ignition switch (12 V DC)

ON/OFF.

Orange/white

To lighting switch terminal.

Black (ground)

To vehicle (metal) body.

Violet/white

Of the two lead wires connected to the back lamp, connect

the one in which the voltage changes when the gear shift

is in the REVERSE (R) position. This connection enables

the unit to sense whether the car is moving forwards or

backwards.

Blue/white

Connect to system control terminal of the power amp (max.

300 mA 12 V DC).

Light green

Used to detect the ON/OFF status of the parking brake. This

CAUTION

 Secure all wiring with cable clamps or electrical tape.

Do not allow any bare wiring to remain exposed.



Do not directly connect the yellow lead of this product

to the vehicle battery. If the lead is directly connected

to the battery, engine vibration may eventually cause

the insulation to fail at the point where the wire

passes from the passenger compartment into the

engine compartment. If the yellow lead’s insulation

tears as a result of contact with metal parts, short-

circuiting can occur, resulting in considerable danger.



It is extremely dangerous to allow cables to become

wound around the steering column or shift lever. Be

sure to install this product, its cables, and wiring

away in such so that they will not obstruct or hinder

driving.



Make sure that the cables and wires will not interfere

with or become caught in any of the vehicle’s moving

parts, especially the steering wheel, shift lever,

parking brake, sliding seat tracks, doors, or any of the

vehicle’s controls.



Do not route wires where they will be exposed to

high temperatures. If the insulation heats up, wires

may become damaged, resulting in a short circuit or

malfunction and permanent damage to the product.



Do not shorten any leads. If you do, the protection

circuit (fuse holder, fuse resistor or filter, etc.) may

fail to work properly.



Never feed power to other electronic products by

cutting the insulation of the power supply lead of

this product and tapping into the lead. The current

capacity of the lead will be exceeded, causing

overheating.

Before installing this product

 Use this unit with a 12-volt battery and negative grounding

only. Failure to do so may result in a fire or malfunction.

 To avoid shorts in the electrical system, be sure to discon-

nect the (–) battery cable before installation.

To prevent damage

WARNING

 Use speakers over 50 W (output value) and between

4Ωto8Ω(impedancevalue).Donotuse1Ωto3Ω

speakers for this unit.

 The black cable is ground. When installing this unit

or power amp (sold separately), make sure to connect

the ground wire first. Ensure that the ground wire is

properly connected to metal parts of the car’s body.

The ground wire of the power amp and the one of this

unit or any other device must be connected to the car

separately with different screws. If the screw for the

ground wire loosens or falls out, it could result in fire

generation of smoke or malfunction.

Ground wire

Metal parts of car’

s body

POWER AMP

Other devices

(Another electr

onic

device in the car)

 When replacing the fuse, be sure to only use a fuse of

the rating prescribed on this product.



This product cannot be installed in a vehicle without ACC

(accessory) position on the ignition switch.

ACC position No ACC position

 To avoid short-circuiting, cover the disconnected lead with

insulating tape. It is especially important to insulate all

unused speaker leads, which if left uncovered may cause a

short circuit.



For connecting a power amp or other devices to this product,

refer to the manual for the product to be connected.

Notice for the blue/white lead

 When the ignition switch is turned on (ACC ON), a control

signal is output through the blue/white lead. Connect to an

external power amp’s system remote control terminal, the

auto-antenna relay control terminal, or the antenna booster

power control terminal (max. 300 mA 12 V DC). The control

signal is output through the blue/white lead, even if the

audio source is switched off.

This product

3 4 5 67 8

1 Microphone 4 m (13 ft. 1 in.)

(AVH-280BT)

2 This product

3 Antenna jack

4 Wired remote input

Hard-wired remote control adapter can be connected (sold

separately).

Power supply

6 Fuse (10 A)

7 Front output

8 Rear output or subwoofer output

32 < QRD3356-A >< QRD3356-A >

Connection Connection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVH-280BT Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVH-280BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info