Bedienungsanleitung Pioneer AVH-3200BT (Seite 57 von 96) (Englisch)

454798

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

! If the microphone is placed in an unsuitable

position the measurement tone may become

loud and measurement may take a long time,

resulting in battery drainage. Be sure to place

the microphone in the specified location.

Before operating the auto TA and EQ

function

! Perform auto TA and EQ in a quiet place,

with both the car engine and air condition-

ing switched off. Also turn off any car

phones or portable telephones in the car, or

remove them from the car. Sounds other

than the measurement tone (such as sur-

rounding sounds, engine sound, tele-

phones ringing) may prevent correct

measurement of the car’s interior acoustic

characteristics.

! Be sure to perform auto TA and EQ using

the optional microphone. Using another

microphone may prevent measurement, or

result in incorrect measurement of the

car’s interior acoustic characteristics.

! In order to perform auto TA and EQ, the

front speaker must be connected.

! When this unit is connected to a power

amp with input level control, auto TA and

EQ may not be possible if the power amp’s

input level is set below the standard level.

! When this unit is connected to a power

amp with an LPF, turn this LPF off before

performing auto TA and EQ. Also set the

cut-off frequency for the built-in LPF of an

active subwoofer to the highest frequency.

! The time alignment value resulting from

auto TA and EQ has been calculated by a

computer and is the optimum delay time

that will give accurate results. Be sure to

use the resulting value although it may dif-

fer from the actual distance when:

— The reflected sound within the car is

strong and delays occur.

— The LPF on active subwoofers or exter-

nal amps delay the lower sounds.

! Auto TA and EQ changes the audio settings

as follows:

— The fader/balance settings return to the

center position. (Refer to page 49.)

— The equalizer curve switches to Flat.

(Refer to page 46.)

— The front, center and rear speakers will

automatically be adjusted to a high

pass filter setting.

! Pervious settings for auto TA and EQ will

be overwritten.

Performing auto TA and EQ

For details concerning operation, refer to the

operation manual for the multi-channel pro -

cessor.

1 Stop the car in a place that is quiet,

close all the doors, windows and sun roof,

and then turn the engine off.

If the engine is left running, engine noise may

prevent correct auto EQ.

2 Fix the optional microphone in the cen-

ter of the headrest of the driver’s seat, fa-

cing forward.

The auto EQ may differ depending on where

you place the microphone. If desired, place

the microphone on the front passenger seat to

carry out auto EQ.

3 Turn the ignition switch to ON or ACC.

If the car’s air conditioner or heater is turned

on, turn it off. Noise from the fan in the air

conditioner or heater may prevent correct auto

EQ.

# If this unit is turned off, press SRC/OFF to turn

the source on.

Section

Menu operations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVH-3200BT Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVH-3200BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info