Bedienungsanleitung Pioneer AVH-5400DVD (Seite 41 von 72) (Englisch)

649354

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Before operating the auto EQ function

! Carry out auto EQ in as quiet a place as

possible, with the car engine and air condi-

tioning switched off. Also cut power to car

phones or portable telephones in the car, or

remove them from the car before carrying

out auto EQ. Sounds other than the mea-

surement tone (surrounding sounds, en-

gine sound, telephones ringing etc.) may

prevent correct measurement of the car in-

terior acoustic characteristics.

! Be sure to carry out auto EQ using the op-

tional microphone. Using another micro-

phone may prevent measurement, or result

in incorrect measurement of the car inter-

ior acoustic characteristics.

! In order to perform auto EQ, the front

speaker must be connected.

! When this unit is connected to a power

amp with input level control, auto EQ may

not be possible if the power amp’s input

level is set below the standard level.

! When this unit is connected to a power

amp with an LPF, turn this LPF off before

performing auto EQ. Also set the cut-off fre-

quency for the built-in LPF of an active sub-

woofer to the highest frequency.

! The distance has been calculated by com-

puter to be the optimum delay to give accu-

rate results for the circumstances, so

please continue to use this value.

— The reflected sound within the car is

strong and delays occur.

— The LPF on active subwoofers or exter-

nal amps delay the lower sounds.

! Auto EQ changes the audio settings as fol-

lows:

— The fader/balance settings return to the

center position. (Refer to Using fader/

balance adjustment on page 29.)

— The equalizer curve switches to Flat.

(Refer to Recalling equalizer curves on

page 29.)

— The front, center and rear speakers will

automatically be adjusted to a high

pass filter setting.

! Previous settings for auto EQ will be over-

written.

Performing auto EQ

1 Stop the car in a place that is quiet,

close all the doors, windows and sun roof,

and then turn the engine off.

If the engine is left running, engine noise may

prevent correct auto EQ.

2 Fix the optional microphone in the cen-

ter of the headrest of the driver’s seat, fa-

cing forward.

The auto EQ may differ depending on where

you place the microphone. If desired, place

the microphone on the front passenger seat to

carry out auto EQ.

3 Turn the ignition switch to ON or ACC.

If the car’s air conditioner or heater is turned

on, turn it off. Noise from the fan in the air

conditioner or heater may prevent correct auto

EQ.

4 Display the system menu.

Refer to Introduction of menu operations on

page 28.

5 Touch Auto EQ Measurement to enter

auto EQ measurement mode.

6 Plug the microphone into the micro-

phone input jack on this unit.

7 Touch Start to start auto EQ.

Section

Menu operations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVH-5400DVD Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info