Bedienungsanleitung Pioneer AVH-P4000DVD (Seite 74 von 96) (Englisch)

454822

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

LOW (low)—MID (mid)—HIGH (high)

7 Touch b and then touch c or d to se-

lect the center frequency of selected band.

Touch c or d until the desired frequency ap-

pears in the display.

40Hz—50Hz—63Hz—80Hz—100Hz—125Hz

—160Hz—200Hz—250Hz—315Hz—400Hz—

500Hz—630Hz—800Hz—1kHz—1.25kHz—

1.6kHz—2kHz—2.5kHz—3.15kHz—4kHz—

5kHz—6.3kHz—8kHz—10kHz—12.5kHz

8 Touch b and then touch c or d to ad-

just the equalizer level.

Each time you touch c or d it increases or de-

creases the equalizer level. +12 to –12 is dis-

played as the level is increased or decreased.

9 Touch b and then touch c or d to se-

lect the desired Q factor.

Each time you touch c or d switches between

the following Q factor:

NARROW (narrow)—WIDE (wide)

# You can adjust parameters for each band of

the other speakers in the same way.

Note

You can select a center frequency for each band.

You can change the center frequency in 1/3-oc-

tave steps, but you cannot select frequencies that

have intervals shorter than 1 octave among the

center frequencies of the three bands.

Using the auto-equalizer

The auto-equalizer is the equalizer curve cre-

ated by auto TA and EQ (refer to Auto TA and

EQ (auto-time alignment and auto-equalizing)

on this page).

You can turn the auto-equalizer on or off.

1 Touch NEXT twice on the DSP function

menu.

2 Touch AUTO EQ.

# You cannot use this function if auto TA and

EQ has not been carried out.

3 Touch d to turn the auto-equalizer on.

# To turn auto-equalizer off, touch c.

Auto TA and EQ (auto-time

alignment and auto-equalizing)

The auto-time alignment is automatically ad-

justed for the distance between each speaker

and the listening position.

The auto-equalizer automatically measures

the car interior acoustic characteristics, and

then creates the auto-equalizer curve based

on that information.

WARNING

To prevent accidents, never carry out auto TA and

EQ while driving. When this function measures

the car interior acoustic characteristics to create

an auto-equalizer curve, a loud measurement

tone (noise) may be outputted from the speakers.

CAUTION

! Carrying out auto TA and EQ under the follow-

ing conditions may damage the speakers. Be

sure to check the conditions thoroughly be-

fore carrying out auto TA and EQ.

— When speakers are incorrectly connected.

(e.g., When a rear speaker is connected to

a subwoofer output.)

— When a speaker is connected to a power

amp delivering output higher than the

speaker’s maximum input power capabil-

ity.

! If the microphone is placed in an unsuitable

position the measurement tone may become

loud and measurement may take a long time,

resulting in a drain on battery power. Be sure

to place the microphone in the specified loca-

tion.

Available accessori es

Section

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVH-P4000DVD Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVH-P4000DVD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info