Bedienungsanleitung Pioneer AVH-X3700DAB (Seite 44 von 66) (Englisch)

649369

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

Using the equalizer

Recalling equalizer curves

There are seven stored equalizer curves that you can easily recall

at any time. Here is a list of the equalizer curves:

●

S.Bass is a curve in which only low-pitched sound is boosted.

●

Powerful is a curve in which low- and high-pitched sounds

are boosted.

●

Natural is a curve in which low- and high-pitched sounds

are slightly boosted.

●

Vocal is a curve in which the midrange, which is the human

vocal range, is boosted.

●

Flat is a flat curve in which nothing is boosted.

●

Custom1 is an adjusted equalizer curve that you create. If

you select this curve, the effect is applied to all AV sources.

●

Custom2 is an adjusted equalizer curve that you create. If

you select this curve, the effect is applied to all AV sources.

The default setting is “Powerful”.

1 Display the “Audio” setting screen.

 Displaying the “Audio” setting screen on page 42

2 Touch [Graphic EQ].

3 Touch the equalizer you want.

Customizing the equalizer curves

You can adjust the currently selected equalizer curve setting

as desired. Adjustments can be made with a 13-band graphic

equalizer.

If you make adjustments when a curve “S.Bass”, “Powerful”,

“Natural”, “Vocal”, or “Flat” is selected, the equalizer curve

settings will be changed to “Custom1” mandatorily.

If you make adjustments when the “Custom2” curve is

selected for example, the “Custom2” curve will be updated.

“Custom1” and “Custom2” curves can be created common

to all sources.

1 Display the “Audio” setting screen.

 Displaying the “Audio” setting screen on page 42

2 Touch [Graphic EQ].

3 Select a curve that you want to use as the basis

of customizing.

4 Touch the frequency for which you want to

adjust the level.

p If you trail a finger across the bars of multiple equalizer

bands, the equalizer curve settings will be set to the value of

the touched point on each bar.

Using the auto-adjusted equalizer

You can set the auto-adjusted equalizer to suit the vehicle’s

acoustics. To use this function, the vehicle’s acoustics must be

measured in advance.



Adjusting the equalizer curve automatically (Auto EQ) on page

To manually adjust the equalizer curve, set “Auto EQ&TA” to

“Off”.

1 Display the “Audio” setting screen.

 Displaying the “Audio” setting screen on page 42

2 Touch “[Auto EQ&TA] to switch “On” or “Off”

(default).

Adjusting the equalizer curve

automatically (Auto EQ)

By measuring the vehicle’s acoustics, the equalizer curve can be

adjusted automatically to suit the vehicle interior.

WARNING

A loud tone (noise) may be emitted from the speakers when

measuring the vehicle’s acoustics. Never perform Auto EQ

measurement while driving.

CAUTION

● Thoroughly check the conditions before performing Auto

EQ, as the speakers may be damaged if this is performed

under the following conditions:

●

When the speakers are incorrectly connected. (For

example, when a rear speaker is connected as a subwoofer

output.)

●

When a speaker is connected to a power amp delivering

output higher than the speaker’s maximum input power

capability.

●

If a microphone for acoustical measurement (sold

separately) is not placed in an appropriate location, the

measurement tone may become loud and measurement

may take a long time, resulting in battery drainage. Be sure

to place the microphone in the specified location.

Before operating the Auto EQ

function

● Perform Auto EQ in as quiet a place as possible, with the

vehicle engine and air conditioning switched off. Also, cut

power to car phones or cellular phones in the vehicle, or

remove them in advance. Surrounding sounds may prevent

correct measurement of the vehicle’s acoustics.

●

Be sure to use the microphone for acoustical measurement

(sold separately). Using another microphone may prevent

measurement, or result in incorrect measurement of the

vehicle’s acoustics.

●

To perform Auto EQ, the front speakers must be connected.

● When this product is connected to a power amp with input

level control, Auto EQ may be impossible if the power amp’s

input level is set below the standard level.

●

When this product is connected to a power amp with an LPF

(low pass filter), turn the LPF off before performing Auto EQ.

Also, set the cut-off frequency for the built-in LPF of an active

subwoofer to the highest frequency.

●

The distance has been calculated by a computer to provide

optimum delay to ensure accurate results. Do not change

this value.

— The reflected sound within the vehicle is strong and delays

occur.

— The LPF on active subwoofers or external amps delay the

lower sounds.

●

If an error occurs during measurement, check the following

before measuring the vehicle’s acoustics.

— Front speakers (left/right)

— Rear speakers (left/right)

— Noise

— Microphone for acoustical measurement (sold separately)

— Low battery

Performing Auto EQ

p Auto EQ changes the audio settings as follows:

— The fader/balance settings return to the center position.

 Using balance adjustment on page 42

— “Mute Level” is set to “Off”.



Switching sound muting/attenuation on page 42

Previous settings for Auto EQ will be overwritten.

p Do not press to open or close the panel when you are

using the microphone.

CAUTION

Do not turn off the engine while the measurement is in

progress.

< CRB4947-A >

Audio adjustments

Pioneer AVH-X3700DAB Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVH-X3700DAB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info