649374

Pioneer AVH-X490DAB Seite 40

40
Zoom out
Zoom in
Vorherige Seite
1/57
Nächste Seite
40
Off, Front-L, Front-R, Front, All.
p The default setting is “Off”.
p “All” is not available when “Network Mode” is selected as
the speaker mode.
p If you change the listening position setting, the output
levels of all the speakers will change in conjunction with the
setting.
5 Touch or to input the distance between
the selected speaker and the listening position.
p You can input the value every 2.5 cm (between 0 and 350
cm).
The following speakers are available:
Standard Mode: Front Left, Front Right, Rear Left, Rear Right,
Subwoofer
Network Mode: High Left, High Right, Mid Left, Mid Right,
Subwoofer
p This function is available only when the listening position
setting is set to “Front-L” or “Front-R”.
p To use this function, the vehicle’s acoustics must be meas-
ured in advance.
If you touch [TA On], the time alignment is turned
off mandatorily.
Switching the time alignment
preset
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 38
2 Touch [Time Alignment Preset].
3 Touch the item.
Initial (default):
Sets to the initial setting value.
ATA:
Reflects the result of “A-EQ&TA Measurement” to the
setting value.
Off:
Resets all setting values to 0.
Custom:
Sets to the value adjusted at “Time Alignment”.
p When you adjust the time alignment, the preset item will
switch automatically to “Custom”.
p “Custom” can be selected only when the listening position is
set to “Front-L” or “Front-R”.
Using the equaliser
Recalling equaliser curves
There are seven stored equaliser curves that you can easily recall
at any time. Here is a list of the equaliser curves:
S.Bass is a curve in which only low-pitched sound is boosted.
Powerful is a curve in which low- and high-pitched sounds
are boosted.
Natural is a curve in which low- and high-pitched sounds
are slightly boosted.
Vocal is a curve in which the midrange, which is the human
vocal range, is boosted.
Flat is a flat curve in which nothing is boosted.
Custom1 is an adjusted equaliser curve that you create. If
you select this curve, the effect is applied to all AV sources.
Custom2 is an adjusted equaliser curve that you create. If
you select this curve, the effect is applied to all AV sources.
p The default setting is “Powerful”.
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 38
2 Touch [Graphic EQ].
3 Touch the equaliser.
Customising the equaliser curves
You can adjust the currently selected equaliser curve setting
as desired. Adjustments can be made with a 13-band graphic
equaliser.
p If you make adjustments when a curve “S.Bass”, “Powerful”,
“Natural”, “Vocal”, or “Flat” is selected, the equaliser curve
settings will be changed to “Custom1” mandatorily.
p If you make adjustments when the “Custom2” curve is
selected for example, the “Custom2” curve will be updated.
p “Custom1” and “Custom2” curves can be created common
to all sources.
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 38
2 Touch [Graphic EQ].
3 Select a curve that you want to use as the basis
of customising.
4 Touch the frequency for which you want to
adjust the level.
p If you trail a finger across the bars of multiple equaliser
bands, the equaliser curve settings will be set to the value of
the touched point on each bar.
Setting the auto-adjusted equaliser
You can set the auto-adjusted equaliser to suit the vehicle’s
acoustics. To use this function, the vehicle’s acoustics must be
measured in advance.
The default setting is “Off”.
Refer to Adjusting the equaliser curve automatically (Auto EQ)
on page 40
p To manually adjust the equaliser curve, set “Auto EQ&TA” to
“Off”.
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 38
2 Touch “[Auto EQ&TA] to switch “On” or “Off”.
Adjusting the equaliser curve
automatically (Auto EQ)
By measuring the vehicle’s acoustics, the equaliser curve can be
adjusted automatically to suit the vehicle interior.
WARNING
A loud tone (noise) may be emitted from the speakers when
measuring the vehicle’s acoustics. Never perform Auto EQ
measurement while driving.
CAUTION
Thoroughly check the conditions before performing Auto
EQ, as the speakers may be damaged if this is performed
under the following conditions:
When the speakers are incorrectly connected. (For exam-
ple, when a rear speaker is connected as a subwoofer
output.)
When a speaker is connected to a power amp delivering
output higher than the speaker’s maximum input power
capability.
If a microphone for acoustical measurement (sold
separately) is not placed in an appropriate location, the
measurement tone may become loud and measurement
may take a long time, resulting in battery drainage. Be sure
to place the microphone in the specified location.
Before operating the Auto EQ
function
Perform Auto EQ in as quiet a place as possible, with the
vehicle engine and air conditioning switched off. Also, cut
power to car phones or mobile phones in the vehicle, or
< QRB3687-A >
Audio adjustments
… 40 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

pioneer-avh-x490dab

Suche zurücksetzen

  • Bluetooth kann nicht aufgerufen. Die Funktion ist auf dem Bildschirm nicht aktiviert ( Blass grau) Eingereicht am 28-10-2020 12:20

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer AVH-X490DAB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer AVH-X490DAB

Pioneer AVH-X490DAB Installationsanweisung - Deutsch - 48 seiten

Pioneer AVH-X490DAB Bedienungsanleitung - Deutsch - 63 seiten

Pioneer AVH-X490DAB Installationsanweisung - Englisch, Holländisch - 48 seiten

Pioneer AVH-X490DAB Bedienungsanleitung - Holländisch - 62 seiten

Pioneer AVH-X490DAB Installationsanweisung - Französisch - 48 seiten

Pioneer AVH-X490DAB Bedienungsanleitung - Französisch - 61 seiten

Pioneer AVH-X490DAB Installationsanweisung - Italienisch, Spanisch - 48 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info