Bedienungsanleitung Pioneer AVH-X8600BT (Seite 108 von 156) (Englisch)

649376

108

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

2 Touch the following keys in the follow-

ing order.

The “Audio” screen appears.

3 Touch [Auto EQ&TA] repeatedly until

the desired setting appears.

! Off (default):

Turns the Auto EQ&TA setting off.

! On:

Turns the Auto EQ&TA setting on.

Adjusting the equaliser curve

automatically (Auto EQ)

By measuring the vehicle’s acoustics, the

equaliser curve can be adjusted automatically

to suit the vehicle interior.

WARNING

A loud tone (noise) may be emitted from the

speakers when measuring the vehicle’s acous-

tics. Never perform Auto EQ measurement while

driving.

CAUTION

! Thoroughly check the conditions before per-

forming Auto EQ, as the speakers may be da-

maged if this is performed under the following

conditions:

— When the speakers are incorrectly con-

nected. (For example, when a rear speaker

is connected as a subwoofer output.)

— When a speaker is connected to a power

amp delivering output higher than the

speaker’s maximum input power capabil-

ity.

! If a microphone for acoustical measurement

(sold separately) is not placed in an appropri-

ate location, the measurement tone may be-

come loud and measurement may take a long

time, resulting in battery drainage. Be sure to

place the microphone in the specified loca-

tion.

Before operating the Auto EQ

function

! Perform Auto EQ in as quiet a place as pos-

sible, with the vehicle engine and air condi-

tioning switched off. Also, cut power to car

phones or mobile phones in the vehicle, or

remove them from the vehicle before per-

forming Auto EQ. Sounds other than the

measurement tone (surrounding sounds,

engine sound, telephones ringing, etc.)

may prevent correct measurement of the

vehicle’s acoustics.

! Be sure to perform Auto EQ using the mi-

crophone for acoustical measurement

(sold separately). Using another micro-

phone may prevent measurement, or result

in incorrect measurement of the vehicle’s

acoustics.

! To perform Auto EQ, the front speakers

must be connected.

! When this product is connected to a power

amp with input level control, Auto EQ may

be impossible if the power amp’s input

level is set below the standard level.

! When this product is connected to a power

amp with an LPF (low pass filter), turn the

LPF off before performing Auto EQ. Also,

set the cut-off frequency for the built-in LPF

of an active subwoofer to the highest fre-

quency.

! The distance has been calculated by a

computer to provide optimum delay to en-

sure accurate results. Do not change this

value.

— The reflected sound within the vehicle is

strong and delays occur.

— The LPF on active subwoofers or exter-

nal amps delay the lower sounds.

! If an error occurs during measurement, a

message appears and measurement is

cancelled. Check the following before mea-

suring the vehicle’s acoustics.

Engb

108

Chapter

Audio adjustments

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVH-X8600BT Seite 108

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVH-X8600BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info