Bedienungsanleitung Pioneer AVIC-5100NEX (Seite 6 von 72) (Englisch, Französisch)

611828

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Black plate (6,1)

To prevent damage

WARNING

! Use speakers over 50 W (output value)

and between 4 W to 8 W (impedance value).

Do not use 1 W to 3 W speakers for this

unit.

! The black cable is ground. When instal-

ling this unit or power amp (sold sepa-

rately), make sure to connect the ground

wire first. Ensure that the ground wire is

properly connected to metal parts of the

car’s body. The ground wire of the power

amp and the one of this unit or any other

device must be connected to the car sepa-

rately with different screws. If the screw

for the ground wire loosens or falls out, it

could result in fire generation of smoke or

malfunction.

Ground wire

Metal parts of car’s bod

Power amp

Other devices

(Another electronic

device in the car)

Not supplied for this unit.

! When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

! When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

! This product cannot be installed in a vehi-

cle without ACC (accessory) position on

the ignition switch.

ACC position No ACC position

! To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe-

cially important to insulate all unused

speaker leads, which if left uncovered may

cause a short circuit.

! Attach the connectors of the same color to

the corresponding colored port, i.e., blue

connector to the blue port, black to black,

etc.

! Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

! Since a unique BPTL circuit is employed,

do not directly ground the * side of the

speaker lead or connect the * side of an-

other side of the speaker lead together. Be

sure to connect the * side of the speaker

lead to the * side of the speaker lead on

this product.

Notice for the blue/white lead

! When the ignition switch is turned on (ACC

ON), a control signal is output through the

blue/white lead. Connect to an external

power amp’s system remote control term-

inal, the auto-antenna relay control term-

inal, or the antenna booster power control

terminal (max. 300 mA 12 V DC). The con-

trol signal is output through the blue/white

lead, even if the audio source is switched

off.

! Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive

current drain and malfunction.

! Be sure not to use this lead as the power

supply lead for the auto-antenna or anten-

na booster. Such connection could cause

excessive current drain and malfunction.

<CRD4852-A>6

Section

Connection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-5100NEX Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVIC-5100NEX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info