Bedienungsanleitung Pioneer AVIC-HD1BT (Seite 174 von 192) (Englisch)

6663

174

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

172

Appendix NAVI/AV

Messages and How to React to Them

Messages for navigation functions

The following messages may be displayed by your navigation system.

❒ There are occasions when you may see error messages other than those shown here. In such a

case, follow the instructions given on the display.

Dialing is not possible because the

touch keys for dialing is inactive.

Your phone is out of range for serv-

ice.

Retry after entering within range for

service.

The connection between mobile

phone and the Bluetooth unit (navi-

gation system) cannot be established

now.

Perform the connection process.

The mobile phone is not registered to

the navigation syetem yet.

To use the mobile phone featuring

the Bluetooth wireless technology

with this navigation system, the reg-

istration process is necessary.

Symptom Cause Action (See)

Message When What to do

Irregular speed pulse signal

detected. Please power off the sys-

tem and check the installation. Then,

please re-boot the system and press

“OK”.

If the navigation system does not

receive the vehicle speed pulse.

Consult your Pioneer dealer.

Speed pulse not connected. Calibra-

tion will start without speed pulse.

Accuracy is not fully ensured without

speed pulse.

The speed signal input (pink lead

wire) of the power cable is not con-

nected.

To operate with 3D hybrid mode, con-

nect the speed signal input (pink

lead wire) of the power cable cor-

rectly.

Although it can be operated with

Simple hybrid mode without con-

necting the speed signal input, the

precision of the positioning will be

less accurate.

Vibration detected. Please power off

the system and check the installa-

tion. Then, please re-boot the system

and press “OK”.

The navigation unit is installed in a

place where it may be affected by a

large vibration.

Re-install the navigation unit in a

place where the unit will not be

affected by vibration.

Direction of G sensor is not correct.

Please power off the system and

check the installation. Then, please

re-boot the system and press “OK”.

Direction of G sensor is set incor-

rectly.

See the Installation Manual and set

the direction of the navigation unit

correctly.

Gyro Sensor is not working properly.

Please consult your dealer or Pioneer

service centre.

Abnormal output of Gyrosensor is

detected.

Note down the error code shown on

the screen; turn off the power, and

then contact your nearest Pioneer

service facility.

Positioning is not possible due to the

hardware. Please contact your dealer

or Pioneer service centre.

The location display is not possible

due to failure of hardware.

Consult your dealer.

GPS antenna problem detected.

Please contact your dealer or Pioneer

service centre.

The location display is not possible

due to failure of GPS aerial.

Consult your dealer.

This function is currently unavailable. The screen cannot be displayed with

Vehicle Dynamics Display.

Because the sensor has not been

taught so the sensor information

cannot be acquired.

If the sensor learning status reaches

the Sensor Initialising status or

more, the system is ready to be used.

MAN-HD1BT-SOFTW-EN.book Page 172 Thursday, April 20, 2006 3:47 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-HD1BT Seite 174

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVIC-HD1BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info